Homepage

239 products

  • Sale -15% Airo Soft plamuur 2,5 kg

    Airo Soft filler 2.5 kg

    3 reviews

    A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams

    €37,08 €31,44

  • Sale -14% Airo Supermetall plamuur 1.4 kg

    Airo Supermetall filler 1.4 kg

    5 reviews

    Silver-gray aluminum-based 2K polyester filler for repairing defective aluminum or iron castings. Casting molds can be filled and cracks can be filled. It can be used in bodywork repairs as a tin replacement and for filling over welds. Airo SUPERMETALL's high heat resistance is also noteworthy, namely up to 30 minutes at +220°C without loss of adhesion. After a 20-minute curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Aluminum - Iron casting Do not apply on - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 1% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams

    €48,67 €41,95

  • Sale -15% Airo TOP Primefill lichtgrijs 500ml

    Airo TOP Primefill light gray 500ml

    4 reviews

    Airo TOP Primefill is a new formula primer in an aerosol can. Because it's in an aerosol can, you can easily reach all areas for treatment. The primer can be applied as a fine finish and dries very quickly. Once dry, it can be sanded to a smooth, pore-free surface. Exceptional adhesion to plastic, metal, galvanized and galvanized sheet metal, aluminum, wood, and painted surfaces. Available in different colours.

    €20,85 €17,71

  • Sale -15% Airo TOP Primefill wit 500ml

    Airo TOP Primefill white 500ml

    3 reviews

    Airo TOP Primefill is a new formula primer in an aerosol can. Because it's in an aerosol can, you can easily reach all areas for treatment. The primer can be applied as a fine finish and dries very quickly. Once dry, it can be sanded to a smooth, pore-free surface. Exceptional adhesion to plastic, metal, galvanized and galvanized sheet metal, aluminum, wood, and painted surfaces. Available in different colours.

    €20,79 €17,71

  • Sale -14% Airo Unipol plamuur 0,5 kg/SB

    Airo Unipol filler 0.5 kg/SB

    6 reviews

    Order now = fast shipping!  Order before 5pm and you will receive your order the next working day

    Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 15 grams

    Order now = fast shipping!  Order before 5pm and you will receive your order the next working day

    €13,77 €11,91

  • Sale -14% Airo Verharder MS Acryl 2:1 - 0.5ltr

    Airo Hardener MS Acrylic 2:1 - 0.5ltr

    4 reviews

    Airo Hardener MS Acrylic 2:1 is the appropriate hardener for Airo MS acrylic lacquer. Ideal for smaller quantities of lacquer and spot repairs. Mixing ratio: 2 parts lacquer to 1 part hardener. Suitable for use with - Airo MS Clearcoat Acrylic 2:1 - Airo MS acrylic lacquers Instructions for use Mix 2 parts Airo MS lacquer with 1 part hardener in a clean mixing cup. Stir thoroughly and thin with Airo Acrylic Thinner if necessary. Process the mixture within its pot life of approximately 4 hours at 20°C. Storage and processing advice - Do not process below +15°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - 0.5 liter hardener, packed in a tin

    €19,94 €17,11

  • Sale -16% Indasa Rhynalox White Line schuurrol 25 m

    Indasa Rhynalox White Line Roll 70mmx25m

    1 review

    Order now = fast shipping!  Order before 5pm and you will receive your order the next working day

    The Indasa Rhynalox White Line Rollers are 25-meter rolls. These sanding rollers are used in the automotive repair industry, the composites industry, and the wood, stone, and marble industries. The sheets are suitable for (manually) sanding off old paint and filler layers, for finishing and correcting filler, and also for sanding composite, aluminum, and hardwood. The paper doesn't clump easily and flexes easily, making it easy to reach any spot for sanding.

    Order now = fast shipping!  Order before 5pm and you will receive your order the next working day

    €37,20 €16,93

  • Sale -15% Airo Unipol plamuur 10 kg

    Airo Unipol filler 3 kg

    6 reviews

    Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 60 grams

    €188,13 €151,98

  • Sale -14% Airo Acryl Verdunner

    Airo Acrylic Thinner SHORT - 1 liter

    6 reviews

    Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.

    €15,56 €13,43

  • Sale -15% Airo Epoxy Grund Universele primer 1 ltr Airo Epoxy Grund Universele primer 1 ltr

    Airo Epoxy Grund Universal primer 1 ltr

    7 reviews

    A beige 2-component (spray) primer based on epoxy resin with strong adhesion to various substrates, particularly aluminum and galvanized parts. It cures quickly, is water-resistant, and offers excellent rust protection. After mixing, the primer has a pot life of 8 hours. It is dust-dry after just 20 minutes and sandable after 4 to 5 hours at 20°C. The primer is sanded with a 150 to 240 grit sandpaper after 4 to 5 hours of curing time. Adhesion on which surface? - Steel plate - Iron - Aluminum - Galvanized base - Glass fiber reinforced plastic based on polyester Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If in doubt, degrease the surface with a clean cloth to improve adhesion. Mix the base with the hardener in a 3:1 ratio (add thinner to your liking if necessary). This mixture can be applied with a spray gun with a 1.5 to 1.7 mm nozzle at a pressure of 1.8 to 2 bar. It can be sanded after approximately 4 to 5 hours of curing time or resprayed. Once the product is applied below the temperature of +10°C, the drying time becomes significantly longer. Drying time +20°C - dust dry after 20 minutes, can be sprayed over after 4 hours, complete drying time 12 hours +60°C – drying time 40 minutes (with a layer thickness of approx. 50 µm) Storage and processing advice - Do not process below +10°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of primer, packed in a tin (see image) - liquid hardener paste in a can of 15 grams

    €59,80 €50,80

  • Sale -16% Airo Fix & Seal MS Polymeerkit

    Airo Fix & Seal MS Polymer Kit Gray 290ml

    6 reviews

    Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.

    €13,75 €11,60

  • Sale -16% Airo Foam Abrasive Sheets 115x125mm

    Airo Foam Abrasive Sheets 115x125mm

    5 reviews

    The soft and flexible Airo Foam Abrasive Sheets are designed for sanding profiled surfaces and rounded, hard-to-reach corners by hand. Airo Foam Abrasive Sheets are widely used in the automotive, painting, and garage sectors. The foam layer is easy to grip and applies even pressure, reducing the risk of sanding through the surface. The sheets are packed in a handy dispenser box with 200 tear-off sheets per roll.

    €72,73 €57,90

  • Sale -14% Airo harderpasta voor 2K plamuur

    Airo Hardener paste white 50gr. - tube

    4 reviews

    Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color 2.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.

    €4,65 €4,01

  • Sale -33% Airo Lackspray mat zwart 500ml

    Airo Lackspray matt black 500ml

    6 reviews

    Airo Lacquer Spray is a high-quality lacquer for treating both treated and untreated surfaces. Thanks to its fast drying and excellent coverage, you won't have to wait long. The lacquer is also resistant to petrol, chemicals, and weather influences. It is UV-resistant, lightfast, and has excellent surface hardness. Suitable for metal, wood, pottery, glass, and various types of plastic.

    €14,93 €9,98

  • Sale -15% Airo Metallic plamuur 2,5 kg

    Airo Metallic filler 2.5 kg

    6 reviews

    A silver-gray 2K polyester filler with high elasticity. Ideal for filling weld seams or applying filler to components exposed to vibrating sheet metal. Easy to use and easy to sand. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit. Adhesion on which surface? - Steel plate - Iron casting - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams

    €40,75 €34,83

  • Sale -17% Airo MS Blanke lak Acryl 2:1 - 5ltr

    Airo MS Clearcoat Acrylic 2:1 - 5ltr

    5 reviews

    Acrylic Clearcoat MS is a medium solid clearcoat that can be used in both air-drying and forced-drying modes for automotive, motorcycle, and industrial applications. Acrylic Clearcoat MS features a UV filter and offers high chemical resistance. It is flexible, yet impact and scratch resistant. It has a high gloss and is universally applicable as a topcoat in a conventional or water-based basecoat system. After mixing (depending on the type of hardener), the clearcoat has a pot life of 3 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 30 to 35 minutes at +60°C. Supplied without matching hardener

    €140,42 €117,09

  • Sale -14% Airo Spritzfüller grijs 1,5 kg

    Airo Spritzfüller grey 1.5 kg

    4 reviews

    A gray 2K polyester spray filler with excellent filling properties. It is used in automotive body repair, mechanical engineering, and the furniture industry. After mixing, the filler has a pot life of approximately 20 to 25 minutes. After 30 minutes of drying time at 60°C, the filler can be sanded with a 150 to 240 grit sandpaper. Adhesion on which surface? - Steel plate - Iron - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Galvanized sheet metal - Aluminum - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to be filled and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If necessary, sand with a P80 to P150 grit. Before each application, clean and degrease the entire surface to be painted with silicone remover. Do not apply to thermoplastic or acidic products (reaction primers). Once the filler is dry, sand with a P150 to P240 grit. Too little or too much hardener can cause stains in the topcoat. If necessary, use a maximum of 5% thinner. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Liquid hardener in a plastic jar

    €29,55 €25,44

  • Sale -14% Airo Tack Plastic Superfast 30sec-50ml

    Airo Tack Plastic Superfast 30sec-50ml

    Airo Tack Plastic Mediumfast repairs plastic parts in 120 seconds. This powerful 2K adhesive dries in 120 seconds. Its small size makes it easy to use in a caulking gun with a plastic adapter. Supplied without the required Mixer Tip Round for 2K glue.

    €13,89 €11,96

  • Sale -13% Airo harderpasta voor 2K plamuur

    Airo Liquid Paste - 60 ml

    7 reviews

    Cyclohexanone peroxide, slowed down with phthalic acid ester and diacetone alcohol. As a free-radical additive for the curing of unsaturated polyester resins, which have been pre-accelerated with cobalt. By using the correct ingredients in the hardener, Airo fillers will cure properly within the specified time. No guarantee can be given when using other brands. To be used for - Airo spray filler Instructions for use The liquid hardener is specifically designed for hardening polyester spray fillers. Carefully add 1.7% hardener to the spray filler for proper reaction. This hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as may contact with dirt, ash, rust, or metal grindings. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Transparent liquid hardener in a plastic tube with a screw cap Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.

    €9,70 €8,44

  • Sale -14% Colad Overspuitbare folie 4x300m

    Colad Sprayable film 4x300m

    2 reviews

    The Colad Sprayable Film 4mx300m is a large-format masking film for professional use. The long roll is particularly suitable for intensive use in a busy bodyshop. Specifications - Width: 4 meters - Length: 300 meters - Thickness: approx. 12 microns Supplied as standard - 1 roll of Colad sprayable film 4mx300m

    €99,28 €84,93

  • Sale -13% Deurplamuurmes met houten greep

    Door putty knife 30 cm

    3 reviews

    A sturdy door putty knife with a beechwood handle and a plywood grip. The blade length is 9.5 cm from the handle.

    €11,72 €10,19

  • Sale -13% Airo Grip Sanding Block

    Mirka Hand sanding block 70x125 mm velcro

    7 reviews

    Order now = fast shipping!  Order before 5pm and you will receive your order the next working day

    The Airo Grip Sanding Block has an ergonomic handle for a secure grip. A special connection for a Ø21mm dust extraction system is located on the back. The Velcro sanding base has holes for dust extraction.

    Order now = fast shipping!  Order before 5pm and you will receive your order the next working day

    €47,79 €41,51

  • Sale -11% Mirka Abranet Delta 152mm velcro Mirka Abranet Delta 152mm velcro - P400 uitvoering

    Mirka Abranet 200 mm discs velcro

    1 review

    Delivery time approx. 3 working days  Order before 5pm and you will receive your order the next working day

    Abranet Ace is designed for heavy-duty and demanding sanding applications. Thanks to its optimized net construction and ceramic grit, Abranet Ace offers superior material removal and performance on hardwoods (such as beech and oak) and provides fast results on various other hard surfaces. Abranet Ace is also an ideal product for sanding primers. It delivers fast and effective results and has a very long service life. Technical data Grain: ceramic Bonding: resin over resin Base: polyamide / polyester Sprinkle: closed Color: light red Supplied in boxes of 50 discs

    Delivery time approx. 3 working days  Order before 5pm and you will receive your order the next working day

    €76,52 €59,40

  • Sale -15% Airo Fix & Seal MS Polymeerkit

    Airo Fix & Seal MS Polymer kit white 290ml

    5 reviews

    Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.

    €13,65 €11,60


You have seen 48 out of 239 products

© 2014-2026 Plamuren.com, Design: LYNX Media

  • Apple Pay
  • Bancontact
  • Google Pay
  • iDEAL Wero
  • Klarna
  • Maestro
  • Mastercard
  • PayPal
  • Shop Pay
  • Visa