Homepage
-
Airo Unipol filler 2.5 kg
Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-hardening primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€36,11 €29,06
-
Airo Unipol filler 1.5 kg
Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 40 grams
€26,78 €22,42
-
Airo Faserplast filler 2 kg
Faserplast is an olive-green, fiberglass-based 2K polyester filler for working through rusted bodywork parts. This filler is a perfect blend of filler and short polyester fibers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit! Adhesion on which surface? - Steel plate - Galvanized metal sheet Do not apply on - Aluminum - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€26,44 €22,80
-
Airo Soft filler 1.5 kg
A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - White hardener paste in plastic tube of 40 grams
€26,11 €21,81
-
Airo Unipol filler 0.5 kg/SB
Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 15 grams
€13,48 €10,03
-
Airo Unipol filler 1 kg
Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€22,33 €15,52
-
Airo Acrylic Thinner NORMAL - 1 liter
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€15,68 €10,45
-
€69,48 €61,28
-
Airo hardener for acrylic Primefill Fuller 4:1 - 250 ml
A high solids hardener for the Airo Acryl Primefill 4:1. (excl. matching quantity of Airo Acryl Primefill)
€13,78 €9,67
-
Airo Unipol filler 3 kg
Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 60 grams
€148,69 €134,36
-
Airo Fix & Seal MS Polymer Kit Gray 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€12,59 €9,76
-
Airo Fix & Seal MS Polymer Kit Black 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€12,59 €9,76
-
Airo Flexi filler 0.5 kg/SB
A fast-curing gray, elastic 2K polyester filler with excellent adhesion to various plastics. Ideal for repairing damaged bumpers and spoilers. Can be overpainted with acrylic filler and 2K lacquers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Bumpers and spoilers made of plastic or polyester Do not apply on - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 15 grams Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€21,23 €11,41
-
Airo HS Profit Line Clear coat 2:1 - 1ltr
Acryl Klarlack HS Ultra Plus bevat niet meer dan maximaal 420 gr. oplosmiddel per liter spuitklare oplossing. Hij wordt toegepast als blanke lak op metallic basis lak of unikleuren. Hij is bestand tegen chemische en mechanische belastingen. De lak droogt op met een glanzend en hard oppervlak. De lakfilms zijn elastisch en kras vast. Airo Acryl Klarlack HS Ultra Plus is weer- en lichtbestendig, zelfs onder zware klimatologische omstandigheden.Na vermenging (afhankelijk van type verharder) heeft de blanke lak een pot-life van 1 tot 6 uur bij +20 °C. Na 7 minuten uitdampen, droogt de lak in 10 tot 45 minuten bij +60 °C.
€31,55 €28,14
-
Airo MS Clearcoat Acrylic 2:1 - 1ltr
Acrylic Clearcoat MS is a medium solid clearcoat that can be used in both air-drying and forced-drying modes for automotive, motorcycle, and industrial applications. Acrylic Clearcoat MS features a UV filter and offers high chemical resistance. It is flexible, yet impact and scratch resistant. It has a high gloss and is universally applicable as a topcoat in a conventional or water-based basecoat system. After mixing (depending on the type of hardener), the clearcoat has a pot life of 3 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 30 to 35 minutes at +60°C. Supplied without matching hardener
€25,68 €20,71
-
Airo MS Clearcoat Acrylic 2:1 - 5ltr
Acrylic Clearcoat MS is a medium solid clearcoat that can be used in both air-drying and forced-drying modes for automotive, motorcycle, and industrial applications. Acrylic Clearcoat MS features a UV filter and offers high chemical resistance. It is flexible, yet impact and scratch resistant. It has a high gloss and is universally applicable as a topcoat in a conventional or water-based basecoat system. After mixing (depending on the type of hardener), the clearcoat has a pot life of 3 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 30 to 35 minutes at +60°C. Supplied without matching hardener
€109,43 €98,59
-
Airo Multi filler 1 kg
This is a beige 2K polyester filler that can be used as an alternative to Unipol. Airo Multi is a slightly finer and more flexible filler than Unipol. This filler can be used as a normal or fine filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€18,56 €15,09
-
Airo Multi filler 2.5 kg
This is a beige 2K polyester filler that can be used as an alternative to Unipol. Airo Multi is a slightly finer and more flexible filler than Unipol. This filler can be used as a normal or fine filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€34,11 €29,50
-
Airo Multi-Green filler 1.6 kg
This light green 2K polyester filler is made with NEW raw materials and contains fewer solvents. Airo Multi Green is a fine filler that can be used universally as a coarse or finishing filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-hardening primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€28,33 €22,56
-
Airo Nitro mixer 0.1kg
A gray-green, fast-drying 1K filler based on nitrocellulose resin, packaged in an easy-to-squeeze tube. This filler is ideal for removing minor damage such as scratches or stone chips. Smoothing out minor imperfections is also no problem. The filler is easy to apply with a putty knife or with your finger for difficult areas. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from underneath, for example, with a wooden surface. After allowing the filler to dry for 20 minutes, it can be sanded with grit P180 to P400. When applying multiple (thin) coats, allow approximately one hour for drying between each coat. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image)
€8,24 €5,65
-
Airo Plastic filler 2.5 kg
White 2K polyester filler with a wide range of applications. Ideal for all filler work in auto body repair, carpentry, and furniture manufacturing. Suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams
€31,99 €26,47
-
Airo Polyester thinner 1ltr
Reactive thinner for polyester products. Unlike nitro, acrylic, or synthetic resin thinners, Airo Polyester Thinner reacts with polyester resins and is chemically incorporated into the resin molecule. NB: Polyester thinner is sensitive to moisture. Close the packaging tightly after use. To be used for: - Airo Unispray - Airo Plamuren (Unipol, Soft, Plastic, ed.) - Airo Spritzfüller - Other Airo polyester products. Instructions for use Add a maximum of 5% to 10% thinner to products. This is because the Airo Polyester thinner doesn't evaporate but reacts with the polyester resin. The properties of the polyester products may change if the Airo Polyester thinner is too high. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Indicated amount of thinner, packed in a tin (see image)
€21,55 €16,01
-
Airo Supermetall filler 1.4 kg
Silver-gray aluminum-based 2K polyester filler for repairing defective aluminum or iron castings. Casting molds can be filled and cracks can be filled. It can be used in bodywork repairs as a tin replacement and for filling over welds. Airo SUPERMETALL's high heat resistance is also noteworthy, namely up to 30 minutes at +220°C without loss of adhesion. After a 20-minute curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Aluminum - Iron casting Do not apply on - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 1% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
€39,59 €35,68
-
Airo Tack Metall metal bonding 50ml
Airo Tack Metall was specifically developed for metal bonding. This powerful 2K adhesive dries air-drying. Its compact size makes it easy to use in a caulking gun with a plastic adapter. Supplied without the required Mixer Tip Round for 2K glue.
€15,83 €11,07
You have seen 24 out of 241 products