Best seller
-
Genuine English putty knife 8 cm - Lion series 505
A genuine ENGLISH putty knife made of high-quality steel. It features a beautifully and expertly sharpened blade, made in Germany. The tang is fully integrated into the handle for added stability. The blade features a forged bolster and brass band, and the handle is made of polished rosewood.
€57,80 €48,26
-
Genuine English putty knife 6 cm - Lion series 505
A genuine ENGLISH putty knife made of high-quality steel. It features a beautifully and expertly sharpened blade, made in Germany. The tang is fully integrated into the handle for added stability. The blade features a forged bolster and brass band, and the handle is made of polished rosewood.
€51,23 €42,91
-
Genuine English putty knife 14 cm - Lion series 505
A genuine ENGLISH putty knife made of high-quality steel. It features a beautifully and expertly sharpened blade, made in Germany. The tang is fully integrated into the handle for added stability. The blade features a forged bolster and brass band, and the handle is made of polished rosewood.
€87,81 €74,73
-
Genuine English putty knife 12 cm - Lion series 505
A genuine ENGLISH putty knife made of high-quality steel. It features a beautifully and expertly sharpened blade, made in Germany. The tang is fully integrated into the handle for added stability. The blade features a forged bolster and brass band, and the handle is made of polished rosewood.
€73,01 €63,00
-
Dosing device Didoc-S 1.5kg tubes
This specially designed dispenser allows you to adjust the ratio of hardener to filler. If more or less hardener is needed, you can adjust the dispenser manually. The ergonomic handle and trigger reduce strain on the user. The discharge mechanism has a backlash to prevent material from leaking out of the cartridges. The included cover plate can be used to close the container after use. It is a solid device with a neat finish. Made of very sturdy plastic and solid steel components. Adjustable to three settings, the hardener is released slowly, normally, or quickly when dispensing filler. Ideal for warm or cold environments, for example! The device can be used with 1.5kg tubes.
€255,41 €215,08
-
Door putty knife 50 cm
A sturdy door putty knife with a beechwood handle and a plywood grip. The blade length is 9.5 cm from the handle.
€21,03 €17,66
-
Door putty knife 30 cm
A sturdy door putty knife with a beechwood handle and a plywood grip. The blade length is 9.5 cm from the handle.
€11,72 €10,19
-
Colad pump fluid syringe EPDM
The Colad EPDM Pump Fluid Syringe is specially crafted from EPDM rubber, which is resistant to aggressive solvents. This makes it suitable for use with solvent-based cleaners and thinners. Scope of application - Spraying solvent-based cleaning agents - Spraying thinners and degreasers - Use with aggressive chemical liquids Properties - EPDM rubber resistant to solvents - Durable construction for intensive use - Fine spray Supplied as standard - 1x Colad pump fluid syringe EPDM
€39,38 €33,53
-
Colad Sprayable film 4x300m
The Colad Sprayable Film 4mx300m is a large-format masking film for professional use. The long roll is particularly suitable for intensive use in a busy bodyshop. Specifications - Width: 4 meters - Length: 300 meters - Thickness: approx. 12 microns Supplied as standard - 1 roll of Colad sprayable film 4mx300m
€82,28 €69,93
-
Airo hardener for acrylic Primefill Fuller 4:1 - 1 liter
A high solids hardener for the Airo Acryl Primefill 4:1. (excl. matching quantity of Airo Acryl Primefill)
€31,72 €26,57
-
Airo Tack Plastic Superfast 30sec-50ml
Airo Tack Plastic Mediumfast repairs plastic parts in 120 seconds. This powerful 2K adhesive dries in 120 seconds. Its small size makes it easy to use in a caulking gun with a plastic adapter. Supplied without the required Mixer Tip Round for 2K glue.
€12,98 €11,18
-
Airo Superflex filler 1 kg
pIs a very white 2K filler. This polyester filler is characterized by its maximum fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
€17,71 €15,32
-
Airo Spritzfüller grey 1.5 kg
A gray 2K polyester spray filler with excellent filling properties. It is used in automotive body repair, mechanical engineering, and the furniture industry. After mixing, the filler has a pot life of approximately 20 to 25 minutes. After 30 minutes of drying time at 60°C, the filler can be sanded with a 150 to 240 grit sandpaper. Adhesion on which surface? - Steel plate - Iron - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Galvanized sheet metal - Aluminum - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to be filled and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If necessary, sand with a P80 to P150 grit. Before each application, clean and degrease the entire surface to be painted with silicone remover. Do not apply to thermoplastic or acidic products (reaction primers). Once the filler is dry, sand with a P150 to P240 grit. Too little or too much hardener can cause stains in the topcoat. If necessary, use a maximum of 5% thinner. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Liquid hardener in a plastic jar
€27,62 €23,78
-
Airo Soft filler 1 kg
A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
€16,61 €14,31
-
Airo Polyester thinner 1ltr
Reactive thinner for polyester products. Unlike nitro, acrylic, or synthetic resin thinners, Airo Polyester Thinner reacts with polyester resins and is chemically incorporated into the resin molecule. NB: Polyester thinner is sensitive to moisture. Close the packaging tightly after use. To be used for: - Airo Unispray - Airo Plamuren (Unipol, Soft, Plastic, ed.) - Airo Spritzfüller - Other Airo polyester products. Instructions for use Add a maximum of 5% to 10% thinner to products. This is because the Airo Polyester thinner doesn't evaporate but reacts with the polyester resin. The properties of the polyester products may change if the Airo Polyester thinner is too high. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Indicated amount of thinner, packed in a tin (see image)
€20,51 €17,78
-
Airo Nautic Ultra Light filler 0.48 kg/SB
A light gray 2K epoxy resin filler with a wide range of applications. It has a very low specific weight with a density of 0.5-0.7 g/l (lighter than water). It cures quickly, is easy to sand, and is water-resistant! After mixing, the filler has a pot life of approximately 15 to 25 minutes. After 6 to 7 hours of curing at 20°C, the filler can be sanded with a P80 to P280 grit sandpaper. It has excellent adhesion to sheet steel, (cast) iron, aluminum, and fiberglass components. It is also suitable for removing osmosis damage from fiberglass boats. Adhesion on which surface? - Steel plate - Cast iron - Aluminum - Fiber optic components Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Apply the desired amount of filler to the putty knife and mix it with approximately 50% hardener for the best result. Try not to work the filler for longer than 15 to 25 minutes, as drying grains may develop in the filler after this time. After 6 to 7 hours of curing, the filler can be sanded. If the temperature is below 20°C, the curing time will be longer. After curing and sanding, the Nautic filler can be finished directly with almost any paint system. For steel or aluminum boats, a 2K anti-corrosion primer should be applied before filling. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Preferably process between +18°C and +25°C - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Special hardener paste in a tin
€32,93 €28,47
-
Airo Nautic filler 0.6kg/SB
A gray 2K epoxy resin-based filler with a wide range of applications. This special epoxy filler can be used above, below, and above the waterline. It cures quickly, is easy to sand, and is water-resistant. Suitable for removing osmosis damage from fiberglass boats. The filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Cast iron - Aluminum - Fiber optic components Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Apply the desired amount of filler to the putty knife and mix it with approximately 50% hardener for the best result. Try not to work the filler for longer than 15 to 20 minutes, as drying grains may develop in the filler after this time. After 6 to 7 hours of curing, the filler can be sanded. If the temperature is below 20°C, the curing time will be longer. For steel or aluminum boats, a 2K anti-corrosion primer should be applied before filling. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Preferably process between +18°C and +25°C - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Special hardener paste in a tin
€29,22 €24,79
-
Airo Multi filler 2.5 kg
This is a beige 2K polyester filler that can be used as an alternative to Unipol. Airo Multi is a slightly finer and more flexible filler than Unipol. This filler can be used as a normal or fine filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€38,43 €32,75
-
Airo Multi filler 1 kg
This is a beige 2K polyester filler that can be used as an alternative to Unipol. Airo Multi is a slightly finer and more flexible filler than Unipol. This filler can be used as a normal or fine filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€19,83 €16,76
-
Airo MS Clearcoat Acrylic 2:1 - 5ltr
Acrylic Clearcoat MS is a medium solid clearcoat that can be used in both air-drying and forced-drying modes for automotive, motorcycle, and industrial applications. Acrylic Clearcoat MS features a UV filter and offers high chemical resistance. It is flexible, yet impact and scratch resistant. It has a high gloss and is universally applicable as a topcoat in a conventional or water-based basecoat system. After mixing (depending on the type of hardener), the clearcoat has a pot life of 3 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 30 to 35 minutes at +60°C. Supplied without matching hardener
€131,23 €109,43
-
Airo Masking Tape 50mm x 50m
High-quality masking tape. This product is heat-resistant up to 80°C. The tape is stretchable and tear-resistant, making it easy to use even when applying primer. It is solvent-resistant and leaves no adhesive residue. Available in various sizes. This masking tape is suitable for automotive repair, industrial applications, and painting.
€6,43 €4,80
-
Airo Masking Tape 38mm x 50m
High-quality masking tape. This product is heat-resistant up to 80°C. The tape is stretchable and tear-resistant, making it easy to use even when applying primer. It is solvent-resistant and leaves no adhesive residue. Available in various sizes. This masking tape is suitable for automotive repair, industrial applications, and painting.
€5,13 €3,64
-
Airo Masking Tape 25mm x 50m
High-quality masking tape. This product is heat-resistant up to 80°C. The tape is stretchable and tear-resistant, making it easy to use even when applying primer. It is solvent-resistant and leaves no adhesive residue. Available in various sizes. This masking tape is suitable for automotive repair, industrial applications, and painting.
€3,76 €2,43
-
Airo Lackspray glossy black 500ml
Airo Lacquer Spray is a high-quality lacquer for treating both treated and untreated surfaces. Thanks to its fast drying and excellent coverage, you won't have to wait long. The lacquer is also resistant to petrol, chemicals, and weather influences. It is UV-resistant, lightfast, and has excellent surface hardness. Suitable for metal, wood, pottery, glass, and various types of plastic.
€13,84 €9,79
You have seen 72 out of 242 products