Best seller
-
Airo TOP Primefill light gray 500ml
Airo TOP Primefill is a new formula primer in an aerosol can. Because it's in an aerosol can, you can easily reach all areas for treatment. The primer can be applied as a fine finish and dries very quickly. Once dry, it can be sanded to a smooth, pore-free surface. Exceptional adhesion to plastic, metal, galvanized and galvanized sheet metal, aluminum, wood, and painted surfaces. Available in different colours.
€19,49 €16,55
-
Airo Superflex filler 2.5 kg
This is a very white 2K filler. This polyester filler is characterized by its exceptional fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams
€35,50 €30,29
-
Airo Nautic Ultra Light filler 1.8 kg
A light gray 2K epoxy resin filler with a wide range of applications. It has a very low specific weight with a density of 0.5-0.7 g/l (lighter than water). It cures quickly, is easy to sand, and is water-resistant! After mixing, the filler has a pot life of approximately 15 to 25 minutes. After 6 to 7 hours of curing at 20°C, the filler can be sanded with a P80 to P280 grit sandpaper. It has excellent adhesion to sheet steel, (cast) iron, aluminum, and fiberglass components. It is also suitable for removing osmosis damage from fiberglass boats. Adhesion on which surface? - Steel plate - Cast iron - Aluminum - Fiber optic components Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Apply the desired amount of filler to the putty knife and mix it with approximately 50% hardener for the best result. Try not to work the filler for longer than 15 to 25 minutes, as drying grains may develop in the filler after this time. After 6 to 7 hours of curing, the filler can be sanded. If the temperature is below 20°C, the curing time will be longer. After curing and sanding, the Nautic filler can be finished directly with almost any paint system. For steel or aluminum boats, a 2K anti-corrosion primer should be applied before filling. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Preferably process between +18°C and +25°C - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Special hardener paste in a tin
€115,52 €99,53
-
Airo Multi-Green filler 1.6 kg
This light green 2K polyester filler is made with NEW raw materials and contains fewer solvents. Airo Multi Green is a fine filler that can be used universally as a coarse or finishing filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-hardening primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€28,10 €24,23
-
Airo MS Clearcoat Acrylic 2:1 - 1ltr
Acrylic Clearcoat MS is a medium solid clearcoat that can be used in both air-drying and forced-drying modes for automotive, motorcycle, and industrial applications. Acrylic Clearcoat MS features a UV filter and offers high chemical resistance. It is flexible, yet impact and scratch resistant. It has a high gloss and is universally applicable as a topcoat in a conventional or water-based basecoat system. After mixing (depending on the type of hardener), the clearcoat has a pot life of 3 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 30 to 35 minutes at +60°C. Supplied without matching hardener
€26,54 €22,98
-
Airo Metallic filler 2.5 kg
A silver-gray 2K polyester filler with high elasticity. Ideal for filling weld seams or applying filler to components exposed to vibrating sheet metal. Easy to use and easy to sand. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit. Adhesion on which surface? - Steel plate - Iron casting - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams
€38,08 €32,55
-
Airo Hardener paste red 40gr. - sleeve
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color 1.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€5,39 €4,63
-
Airo Fix & Seal MS Polymer Kit Black 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€13,00 €10,84
-
Airo Fix & Seal MS Polymer Kit Gray 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€12,85 €10,84
-
Airo HS Profit Line Clear coat 2:1 - 1ltr
Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C.
€32,61 €28,06
-
Airo Washprimer 2:1 - 1 ltr
The green-yellow primer is excellent for rust prevention. Do NOT use as a base for polyester products! After 20 minutes of drying time at 60°C, the primer can be sanded with a 150 to 240 grit sandpaper. Excellent adhesion to galvanised metal sheet, hot-dip galvanised body sheet, steel sheet, aluminium.
€33,44 €28,68
-
Airo Hardener HS Ultra Plus 2:1 -0.5ltr
Hardener for Acrylic Clearcoat HS Ultra Plus in a 2:1 mixing ratio. Available in various hardening options: normal, short, and extra short. The special hardener, combined with Acrylic Clearcoat HS Ultra Plus, produces a high gloss and is non-yellowing. Drying time: -Normally 30 to 35 minutes at +60 °C -Shortly 20 to 25 minutes at +60 °C -Extra short 10 to 15 minutes at +60 °C. Supplied without matching paint
€25,34 €19,28
-
Standard spout kit for 290-310ml tubes
This nozzle kit fits Airo's 290ml and 310ml cartridges. A small blade allows you to adjust the opening size to adjust the dosage. Sold individually.
€0,59 €0,49
-
English putty knife Popular 8cm
A genuine English putty knife made of premium steel and expertly sharpened. The blade features a bolster with a brass band. The handle is made of polished rosewood.
€34,92 €30,02
-
English putty knife Popular 6cm
A genuine English putty knife made of premium steel and expertly sharpened. The blade features a bolster with a brass band. The handle is made of polished rosewood.
€29,14 €24,65
-
English putty knife Popular 4cm
A genuine English putty knife made of premium steel and expertly sharpened. The blade features a bolster with a brass band. The handle is made of polished rosewood.
€24,57 €21,26
-
English putty knife Popular 12cm
A genuine English putty knife made of premium steel and expertly sharpened. The blade features a bolster with a brass band. The handle is made of polished rosewood.
€47,31 €40,38
-
English putty knife Popular 10cm
A genuine English putty knife made of premium steel and expertly sharpened. The blade features a bolster with a brass band. The handle is made of polished rosewood.
€39,24 €33,46
-
Genuine English putty knife 8 cm - Lion series 505
A genuine ENGLISH putty knife made of high-quality steel. It features a beautifully and expertly sharpened blade, made in Germany. The tang is fully integrated into the handle for added stability. The blade features a forged bolster and brass band, and the handle is made of polished rosewood.
€57,80 €48,26
-
Genuine English putty knife 6 cm - Lion series 505
A genuine ENGLISH putty knife made of high-quality steel. It features a beautifully and expertly sharpened blade, made in Germany. The tang is fully integrated into the handle for added stability. The blade features a forged bolster and brass band, and the handle is made of polished rosewood.
€51,23 €42,91
-
Genuine English putty knife 12 cm - Lion series 505
A genuine ENGLISH putty knife made of high-quality steel. It features a beautifully and expertly sharpened blade, made in Germany. The tang is fully integrated into the handle for added stability. The blade features a forged bolster and brass band, and the handle is made of polished rosewood.
€73,01 €63,00
-
Door putty knife 50 cm
A sturdy door putty knife with a beechwood handle and a plywood grip. The blade length is 9.5 cm from the handle.
€21,03 €17,66
-
Door putty knife 30 cm
A sturdy door putty knife with a beechwood handle and a plywood grip. The blade length is 9.5 cm from the handle.
€11,72 €10,19
-
Colad pump fluid syringe EPDM
The Colad EPDM Pump Fluid Syringe is specially crafted from EPDM rubber, which is resistant to aggressive solvents. This makes it suitable for use with solvent-based cleaners and thinners. Scope of application - Spraying solvent-based cleaning agents - Spraying thinners and degreasers - Use with aggressive chemical liquids Properties - EPDM rubber resistant to solvents - Durable construction for intensive use - Fine spray Supplied as standard - 1x Colad pump fluid syringe EPDM
€39,38 €33,53
You have seen 48 out of 234 products