Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with dark color 2.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color 1.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
Order now = fast shipping!
Order before 5pm and you will receive your order the next working day
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with dark color 1kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
Highly reactive polyester resin. Combined with glass mats or glass fabric, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry (non-greasy) and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of resin, packed in a tin (see image) - 2x red hardener paste in plastic tube of 50 grams Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
Highly reactive polyester resin. Combined with glass mats or glass fabric, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry (non-greasy) and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of resin, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams - Glass mat 330g/m2 á 1/2 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
Highly reactive polyester resin. Combined with glass mats or glass fibers, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 8 grams - Glass mat 330g/m2 á 1/8 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
Order now = fast shipping!
Order before 5pm and you will receive your order the next working day
A grayish-green, fast-drying 1K filler based on nitrocellulose synthetic resin. This filler is ideal for removing minor damage such as scratches or stone chips. Smoothing out minor imperfections is also no problem. The filler is easy to apply with a putty knife or with your finger for difficult areas. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from underneath, for example, with a wooden surface. After allowing the filler to dry for 20 minutes, it can be sanded with grit P180 to P400. When applying multiple (thin) coats, allow approximately one hour for drying between each coat. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image)
A gray 2K polyester spray filler with excellent filling properties. It is used in automotive body repair, mechanical engineering, and the furniture industry. After mixing, the filler has a pot life of approximately 20 to 25 minutes. After 30 minutes of drying time at 60°C, the filler can be sanded with a 150 to 240 grit sandpaper. Adhesion on which surface? - Steel plate - Iron - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Galvanized sheet metal - Aluminum - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to be filled and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If necessary, sand with a P80 to P150 grit. Before each application, clean and degrease the entire surface to be painted with silicone remover. Do not apply to thermoplastic or acidic products (reaction primers). Once the filler is dry, sand with a P150 to P240 grit. Too little or too much hardener can cause stains in the topcoat. If necessary, use a maximum of 5% thinner. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Liquid hardener in a plastic jar
A gray 2K epoxy resin-based filler with a wide range of applications. This special epoxy filler can be used above, below, and above the waterline. It cures quickly, is easy to sand, and is water-resistant. Suitable for removing osmosis damage from fiberglass boats. The filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Cast iron - Aluminum - Fiber optic components Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Apply the desired amount of filler to the putty knife and mix it with approximately 50% hardener for the best result. Try not to work the filler for longer than 15 to 20 minutes, as drying grains may develop in the filler after this time. After 6 to 7 hours of curing, the filler can be sanded. If the temperature is below 20°C, the curing time will be longer. For steel or aluminum boats, a 2K anti-corrosion primer should be applied before filling. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Preferably process between +18°C and +25°C - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Special hardener paste in a tin
A gray 2K epoxy resin-based filler with a wide range of applications. This special epoxy filler can be used above, below, and above the waterline. It cures quickly, is easy to sand, and is water-resistant. Suitable for removing osmosis damage from fiberglass boats. The filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Cast iron - Aluminum - Fiber optic components Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Apply the desired amount of filler to the putty knife and mix it with approximately 50% hardener for the best result. Try not to work the filler for longer than 15 to 20 minutes, as drying grains may develop in the filler after this time. After 6 to 7 hours of curing, the filler can be sanded. If the temperature is below 20°C, the curing time will be longer. For steel or aluminum boats, a 2K anti-corrosion primer should be applied before filling. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Preferably process between +18°C and +25°C - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Special hardener paste in a tin
A light gray 2K epoxy resin filler with a wide range of applications. It has a very low specific weight with a density of 0.5-0.7 g/l (lighter than water). It cures quickly, is easy to sand, and is water-resistant! After mixing, the filler has a pot life of approximately 15 to 25 minutes. After 6 to 7 hours of curing at 20°C, the filler can be sanded with a P80 to P280 grit sandpaper. It has excellent adhesion to sheet steel, (cast) iron, aluminum, and fiberglass components. It is also suitable for removing osmosis damage from fiberglass boats. Adhesion on which surface? - Steel plate - Cast iron - Aluminum - Fiber optic components Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Apply the desired amount of filler to the putty knife and mix it with approximately 50% hardener for the best result. Try not to work the filler for longer than 15 to 25 minutes, as drying grains may develop in the filler after this time. After 6 to 7 hours of curing, the filler can be sanded. If the temperature is below 20°C, the curing time will be longer. After curing and sanding, the Nautic filler can be finished directly with almost any paint system. For steel or aluminum boats, a 2K anti-corrosion primer should be applied before filling. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Preferably process between +18°C and +25°C - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Special hardener paste in a tin
A light gray 2K epoxy resin filler with a wide range of applications. It has a very low specific weight with a density of 0.5-0.7 g/l (lighter than water). It cures quickly, is easy to sand, and is water-resistant! After mixing, the filler has a pot life of approximately 15 to 25 minutes. After 6 to 7 hours of curing at 20°C, the filler can be sanded with a P80 to P280 grit sandpaper. It has excellent adhesion to sheet steel, (cast) iron, aluminum, and fiberglass components. It is also suitable for removing osmosis damage from fiberglass boats. Adhesion on which surface? - Steel plate - Cast iron - Aluminum - Fiber optic components Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Apply the desired amount of filler to the putty knife and mix it with approximately 50% hardener for the best result. Try not to work the filler for longer than 15 to 25 minutes, as drying grains may develop in the filler after this time. After 6 to 7 hours of curing, the filler can be sanded. If the temperature is below 20°C, the curing time will be longer. After curing and sanding, the Nautic filler can be finished directly with almost any paint system. For steel or aluminum boats, a 2K anti-corrosion primer should be applied before filling. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Preferably process between +18°C and +25°C - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Special hardener paste in a tin
Faserplast is an olive-green, fiberglass-based 2K polyester filler for working through rusted bodywork parts. This filler is a perfect blend of filler and short polyester fibers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit! Adhesion on which surface? - Steel plate - Galvanized metal sheet Do not apply on - Aluminum - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
A strong, light-yellow polyester resin with long glass fibers that cures quickly. The filler is highly resistant to water, gasoline, mineral oil, diluted acids, and alkalis. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
A strong, light-yellow polyester resin with long glass fibers that cures quickly. The filler is highly resistant to water, gasoline, mineral oil, diluted acids, and alkalis. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
A silver-gray 2K polyester filler with high elasticity. Ideal for filling weld seams or applying filler to components exposed to vibrating sheet metal. Easy to use and easy to sand. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit. Adhesion on which surface? - Steel plate - Iron casting - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams
White 2K polyester filler with a wide range of applications. Ideal for all filler work in auto body repair, carpentry, and furniture manufacturing. Suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
White 2K polyester filler with a wide range of applications. Ideal for all filler work in auto body repair, carpentry, and furniture manufacturing. Suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 15 grams
A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - White hardener paste in plastic tube of 60 grams
A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams
A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
This is a very white 2K filler. This polyester filler is characterized by its exceptional fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - White hardener paste in plastic tube of 60 grams
This is a very white 2K filler. This polyester filler is characterized by its exceptional fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams
