Homepage
-
Airo Nautic filler 0.6kg/SB
A gray 2K epoxy resin-based filler with a wide range of applications. This special epoxy filler can be used above, below, and above the waterline. It cures quickly, is easy to sand, and is water-resistant. Suitable for removing osmosis damage from fiberglass boats. The filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Cast iron - Aluminum - Fiber optic components Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Apply the desired amount of filler to the putty knife and mix it with approximately 50% hardener for the best result. Try not to work the filler for longer than 15 to 20 minutes, as drying grains may develop in the filler after this time. After 6 to 7 hours of curing, the filler can be sanded. If the temperature is below 20°C, the curing time will be longer. For steel or aluminum boats, a 2K anti-corrosion primer should be applied before filling. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Preferably process between +18°C and +25°C - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Special hardener paste in a tin
€29,22 €24,79
-
Airo Nautic Ultra Light filler 0.48 kg/SB
A light gray 2K epoxy resin filler with a wide range of applications. It has a very low specific weight with a density of 0.5-0.7 g/l (lighter than water). It cures quickly, is easy to sand, and is water-resistant! After mixing, the filler has a pot life of approximately 15 to 25 minutes. After 6 to 7 hours of curing at 20°C, the filler can be sanded with a P80 to P280 grit sandpaper. It has excellent adhesion to sheet steel, (cast) iron, aluminum, and fiberglass components. It is also suitable for removing osmosis damage from fiberglass boats. Adhesion on which surface? - Steel plate - Cast iron - Aluminum - Fiber optic components Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Apply the desired amount of filler to the putty knife and mix it with approximately 50% hardener for the best result. Try not to work the filler for longer than 15 to 25 minutes, as drying grains may develop in the filler after this time. After 6 to 7 hours of curing, the filler can be sanded. If the temperature is below 20°C, the curing time will be longer. After curing and sanding, the Nautic filler can be finished directly with almost any paint system. For steel or aluminum boats, a 2K anti-corrosion primer should be applied before filling. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Preferably process between +18°C and +25°C - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Special hardener paste in a tin
€32,93 €28,47
-
Airo Oversprayable static film 4x300m
The Airo 4mx300m Sprayable Static Film is a large-format, self-adhesive masking film for intensive use. The long roll is particularly advantageous for workshops with high masking film usage. Specifications - Width: 4 meters - Length: 300 meters - Adhesion: static (glue-free) Supplied as standard - 1 roll of Airo sprayable static film 4m x 300m
€103,65 €89,85
-
Airo Resprayable static film 5x120m
The Airo Oversprayable Static Film 5m x 120m is a wide, self-adhesive masking film that adheres using static electricity. No adhesive, no residue – ideal for quickly covering vehicle parts. Specifications - Width: 5 meters - Length: 120 meters - Adhesion: static (glue-free) Supplied as standard - 1 roll of Airo spray-on static foil 5mx120m
€71,33 €59,79
-
Airo Resprayable static film 6x100m
The Airo Oversprayable Static Film 6m x 100m is a self-adhesive masking film that adheres to smooth surfaces without adhesive using static electricity. The film is oversprayable and effectively protects against overspray during painting. Specifications - Width: 6 meters - Length: 100 meters - Adhesion: static (glue-free) Scope of application - Covering windows, bumpers and body parts - Protection during spraying work - Professional bodywork workshop Instructions for use Cut the film to the desired length. Press the film onto the surface to be protected – the film adheres using static electricity, not adhesive. After spraying, simply remove the film without leaving any adhesive residue. Supplied as standard - 1 roll of Airo spray-on static foil 6mx100m
€72,79 €59,00
-
Airo Plastic filler 0.5 kg/SB
White 2K polyester filler with a wide range of applications. Ideal for all filler work in auto body repair, carpentry, and furniture manufacturing. Suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 15 grams
€11,90 €9,95
-
Airo Plastic filler 1 kg
White 2K polyester filler with a wide range of applications. Ideal for all filler work in auto body repair, carpentry, and furniture manufacturing. Suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
€17,68 €15,23
-
Airo Quatro Mixer Tips 2k (10 pcs.)
Special mixer tips for mixing (older models) Womix and 2k cartridges, among other things. This attachment slides easily onto the top connection of the products. **NOTE: Does not fit the Airo TACK 2k kits, for this you will need to use the " Airo Mixertip ROUND ". Packed per 10 pieces for an attractive price.
€13,00 €8,52
-
Airo Soft filler 1 kg
A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
€16,61 €14,31
-
Airo Soft filler 3 kg
A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - White hardener paste in plastic tube of 60 grams
€51,03 €43,73
-
Airo Spritzfüller grey 1.5 kg
A gray 2K polyester spray filler with excellent filling properties. It is used in automotive body repair, mechanical engineering, and the furniture industry. After mixing, the filler has a pot life of approximately 20 to 25 minutes. After 30 minutes of drying time at 60°C, the filler can be sanded with a 150 to 240 grit sandpaper. Adhesion on which surface? - Steel plate - Iron - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Galvanized sheet metal - Aluminum - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to be filled and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If necessary, sand with a P80 to P150 grit. Before each application, clean and degrease the entire surface to be painted with silicone remover. Do not apply to thermoplastic or acidic products (reaction primers). Once the filler is dry, sand with a P150 to P240 grit. Too little or too much hardener can cause stains in the topcoat. If necessary, use a maximum of 5% thinner. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Liquid hardener in a plastic jar
€27,62 €23,78
-
Airo Superflex filler 1 kg
pIs a very white 2K filler. This polyester filler is characterized by its maximum fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
€17,71 €15,32
-
Airo Superflex filler 1.5 kg
This is a very white 2K filler. This polyester filler is characterized by its exceptional fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - White hardener paste in plastic tube of 40 grams
€29,64 €25,21
-
Airo Superflex filler 3 kg
This is a very white 2K filler. This polyester filler is characterized by its exceptional fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - White hardener paste in plastic tube of 60 grams
€56,14 €46,80
-
Airo Tack Plastic Universal 120sec-50ml
Airo Tack Plastic Mediumfast repairs plastic parts in 120 seconds. This powerful 2K adhesive dries in 120 seconds. Its small size makes it easy to use in a caulking gun with a plastic adapter. Supplied without the required Mixer Tip Round for 2K glue.
€13,09 €11,18
-
Airo Tack Window sealant MS 290ml
Airo Tack Window sealant is a black MS 1K polymer sealant ideal for bonding windows. Its unique composition provides excellent adhesion to existing window sealant. It also works on glass and ceramic edges without the need for a primer. The Tack Window window sealant is UV-resistant and has very good adhesion.
€27,38 €22,94
-
Airo Unipol filler 3 kg
Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 60 grams
€58,26 €48,80
-
Airo Hardener HS Ultra Plus 2:1 -2.5ltr
Hardener for Acrylic Clearcoat HS Ultra Plus in a 2:1 mixing ratio. Available in various hardening options: normal, short, and extra short. The special hardener, combined with Acrylic Clearcoat HS Ultra Plus, produces a high gloss and is non-yellowing. Drying time: -Normally 30 to 35 minutes at +60 °C -Shortly 20 to 25 minutes at +60 °C -Extra short 10 to 15 minutes at +60 °C. Supplied without matching paint
€91,85 €87,74
-
Airo Hardener for Washprimer 0.5 ltr
The hardener is combined with the Airo Wash Primer. The hardener is specially developed for a perfect bond with the Airo Wash Primer. The hardener is mixed 2:1 with the Wash Primer. Excellent adhesion on galvanized sheet metal, hot-dip galvanized bodywork, steel sheet metal, and aluminum.
€15,31 €10,43
-
Coding rings set of 5 rings + 2 identification charts
The Coding Ring Set consists of 5 colored coding rings and 2 identification cards for clearly labeling Colad pump fluid syringes. By giving each syringe its own color, you prevent confusion between different fluids. Contents of the set - 5 colored coding rings - 2 identification charts for keeping track of color coding Scope of application - Organizing multiple pump fluid syringes - Color coding of fluids in the workshop Instructions for use Attach a coding ring to each pump fluid syringe. Note on the identification chart which color corresponds to which fluid. This way, it's always immediately clear which syringe contains which fluid. Supplied as standard - 5x colored coding ring - 2x identification chart
€9,45 €7,49
-
Colad Vapor-permeable Foil 4mx150m
The Colad Vapor Permeable Film 4m x 150m is a special masking film that allows water vapor to pass through but blocks liquids and overspray. Ideal for use in spray booths and for work where ventilation is important. Specifications - Width: 4 meters - Length: 150 meters - Property: vapour permeable Scope of application - Covering in spray booths - Protection during spraying work with ventilation requirements - Professional bodywork workshop Supplied as standard - 1 roll of Colad vapour-permeable film 4m x 150m
€59,95 €48,45
-
Colad Electronic foil cutter
The Colad Electronic Film Cutter is a professional tool for cutting masking and cover film precisely and quickly. The electric cutter ensures a clean, straight cut without tearing the film. Scope of application - Cutting of sprayable cover film - Cutting masking film - Professional bodywork workshop Instructions for use Load the film into the cutter. Set the desired cutting length. Press the cutting button for an automatic, clean cut. Replace the blade as soon as the cutting quality deteriorates. Supplied as standard - 1x Colad Electronic foil cutter - Spare blades
€24,45 €16,45
-
Colad Fine Dust Mask
The Colad Fine Dust Mask provides reliable protection against fine dust during sanding and grinding work in the bodyshop. The mask is comfortable and lightweight for extended use. Scope of application - Protection when sanding filler and primer - Protection during grinding and cutting work - General dust protection in the workshop Properties - FFP2 protection - Light and comfortable - Elastic headband for a good fit Supplied as standard - Packaging Colad fine dust masks (see packaging for quantity)
€24,55 €17,81
-
Colad Fine dust mask with exhalation valve
The Colad Fine Dust Mask with Exhalation Valve offers protection against fine dust during sanding and grinding. The exhalation valve ensures comfortable wear by quickly expelling the exhaled air. Scope of application - Protection when sanding filler and primer - Protection during grinding work - General dust protection in the workshop Properties - Exhalation valve for comfortable wearing - FFP2 protection - Ergonomic fit Supplied as standard - 1x Colad fine dust mask with exhalation valve
€48,55 €41,76
You have seen 144 out of 233 products