Airo
-
Airo MS Clearcoat Acrylic 2:1 - 1ltr
Acrylic Clearcoat MS is a medium solid clearcoat that can be used in both air-drying and forced-drying modes for automotive, motorcycle, and industrial applications. Acrylic Clearcoat MS features a UV filter and offers high chemical resistance. It is flexible, yet impact and scratch resistant. It has a high gloss and is universally applicable as a topcoat in a conventional or water-based basecoat system. After mixing (depending on the type of hardener), the clearcoat has a pot life of 3 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 30 to 35 minutes at +60°C. Supplied without matching hardener
€26,54 €22,98
-
Airo Metallic filler 2.5 kg
A silver-gray 2K polyester filler with high elasticity. Ideal for filling weld seams or applying filler to components exposed to vibrating sheet metal. Easy to use and easy to sand. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit. Adhesion on which surface? - Steel plate - Iron casting - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams
€38,08 €32,55
-
Airo Masking Tape 50mm x 50m
High-quality masking tape. This product is heat-resistant up to 80°C. The tape is stretchable and tear-resistant, making it easy to use even when applying primer. It is solvent-resistant and leaves no adhesive residue. Available in various sizes. This masking tape is suitable for automotive repair, industrial applications, and painting.
€6,43 €4,80
-
Airo Masking Tape 19mm x 50m
High-quality masking tape. This product is heat-resistant up to 80°C. The tape is stretchable and tear-resistant, making it easy to use even when applying primer. It is solvent-resistant and leaves no adhesive residue. Available in various sizes. This masking tape is suitable for automotive repair, industrial applications, and painting.
€2,72 €1,83
-
Airo Magnetic Foil Cutting Blades
The Airo Magnetic Film Cutting Blades are specially designed for precisely cutting masking and cover film. Their magnetic properties make them easy to store and prevent them from getting lost in the workshop. Scope of application - Cutting masking film - Cutting of cover foil - Removing tape and foil Instructions for use Use the blades only for cutting foil and tape. Replace the blade when it is no longer sharp enough for a clean cut. Store the blades on a magnetic surface or in the included holder for safe storage. Supplied as standard - Set of magnetic foil cutting blades (see packaging for quantity)
€73,02 €64,56
-
Airo Lackspray matt black 500ml
Airo Lacquer Spray is a high-quality lacquer for treating both treated and untreated surfaces. Thanks to its fast drying and excellent coverage, you won't have to wait long. The lacquer is also resistant to petrol, chemicals, and weather influences. It is UV-resistant, lightfast, and has excellent surface hardness. Suitable for metal, wood, pottery, glass, and various types of plastic.
€13,95 €9,33
-
Airo Lackspray primer 500ml
Airo Paint Spray is a high-quality primer for treating both treated and untreated surfaces. Thanks to its fast drying and excellent coverage, you won't have to wait long. The paint is also resistant to petrol, chemicals, and weather influences. It's ideal as a pretreatment for topcoats with nitrocellulose, alkyd resin, and 1K and 2K acrylic paints. Suitable for metal, wood, pottery, glass, and various types of plastic.
€15,55 €9,48
-
Airo Lackspray glossy black 500ml
Airo Lacquer Spray is a high-quality lacquer for treating both treated and untreated surfaces. Thanks to its fast drying and excellent coverage, you won't have to wait long. The lacquer is also resistant to petrol, chemicals, and weather influences. It is UV-resistant, lightfast, and has excellent surface hardness. Suitable for metal, wood, pottery, glass, and various types of plastic.
€13,84 €9,79
-
Airo Plastic Adapter for caulking gun
Adapter for using 50ml cartridges in a traditional caulking gun. This product is designed for Airo Tack products. This is a robust and cost-effective solution compared to purchasing a separate mixing gun. Packed per piece.
€19,95 €17,09
-
Airo GTI Adhesive Cloths
The Airo GTI Tack Cloths are special tack cloths for dusting surfaces immediately before painting or spraying. These cloths remove dust, flies, and small contaminants from the surface without leaving any residue. Scope of application - For painting cars and bodywork - Varnishing furniture and wood - Spray work on various surfaces Instructions for use Unfold the tack cloth and gently smooth it over the surface to be painted. Apply light pressure and move the cloth in one direction. The cloth attracts and traps dust and dirt. Use each cloth only once for optimal results. Store unused cloths in their original packaging. Supplied as standard - Package with adhesive cloths (see package for quantity)
€3,33 €2,79
-
Airo HS Profit Line Clear coat 2:1 - 5ltr
Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C.
€152,94 €133,76
-
Airo HS Profit Line Clear coat 2:1 - 1ltr
Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C.
€32,61 €28,06
-
Airo HS Clearcoat Ultra Plus SET - 5ltr
**This product is a set of clear lacquer with normal hardener** Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C.
€235,52 €207,22
-
Airo HS Clearcoat Ultra Plus SET - 1ltr
**This product is a set of clear lacquer with normal hardener** Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C.
€61,36 €45,22
-
Airo HS Clearcoat Ultra Plus 2:1 - 5ltr
Airo HS Ultra Plus Clearcoat is a high-quality 2K high-solids clearcoat with excellent gloss and durability. It offers excellent resistance to UV radiation, fuels, and weather conditions. Ideal for professional bodywork. Suitable for use on - Acrylic primer (Airo Acryl Füller) - Water-based base coat - Solvent-based base coat Instructions for use Mix 2 parts clearcoat with 1 part Airo Hardener HS Ultra Plus. Thin with Airo Acrylic Thinner if necessary. Spray with a 1.3 to 1.4 mm nozzle at a pressure of 2 to 2.5 bar. Apply 2 coats, allowing 10 to 15 minutes between coats. Allow the coat to dry within the pot life of approximately 4 hours at 20°C. Storage and processing advice - Do not process below +15°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - 5 liters of clear lacquer, packed in a tin - Hardener must be ordered separately
€148,31 €132,71
-
Airo HS Clearcoat Ultra Plus 2:1 - 1ltr
Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C. Supplied without matching hardener
€33,13 €28,50
-
Airo Hardener paste white 50gr. - tube
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color 2.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€4,35 €3,75
-
Airo Hardener paste white 40gr. - sleeve
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color 1.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€5,43 €4,63
-
Airo Hardener paste white 25gr. - tube
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€3,38 €2,89
-
Airo Hardener paste red 25gr. - tube
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with dark color 1kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€3,45 €2,89
-
Airo Hand Cleaner 1ltr
Hand Cleaner is a hand soap for removing glue, sealant, and paint. Unlike other products, this soap is gentle on your hands, preventing them from drying out or irritating. Applying a silicone layer to your hands before working is also no longer necessary with this product.
€26,20 €22,00
-
Airo Grip Pad UNI support pad 150mm
The Airo Grip Pad UNI backing pad 150mm is a universal velcro backing pad for eccentric sanders with a 150mm disc diameter. The pad features optimal ventilation openings for maximum dust extraction and is compatible with various sander brands. Specifications - Diameter: 150mm - Attachment: Velcro (hook and loop) - Number of holes: 15 - Suitable for: eccentric sanders 150mm Instructions for use Remove the old backing pad from the sander. Attach the new Airo Grip Pad UNI by pressing it firmly onto the drive disc. Check that the pad is properly secured before use. Replace the backing pad when the Velcro is worn or the pad is visibly damaged. Compatible with oa - Mirka DEROS and DEXOS - Festool ETS and ETSC - Rupes LHR and iBrid - And various other brands of sanders 150mm
€48,91 €41,73
-
Airo Glass fabric matt 190g/m2 - 1m2
Glass fibre fabric for repairing holes in combination with repair resin on car bodies and glass fibre reinforced plastic parts exposed to high loads. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to the correct size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Glass fiber mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€16,81 €14,09
-
Airo Glass fabric matt 190g/m2 - 0.5m2
Glass fibre fabric for repairing holes in combination with repair resin on car bodies and glass fibre reinforced plastic parts exposed to high loads. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to the correct size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Glass fiber mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€9,35 €7,94
You have seen 96 out of 117 products