Airo
-
Airo Unipol filler 2.5 kg
Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-hardening primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€38,62 €32,26
-
Airo Unipol filler 1.5 kg
Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 40 grams
€29,22 €24,89
-
Airo Soft filler 1.5 kg
A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - White hardener paste in plastic tube of 40 grams
€28,12 €24,21
-
Airo Unispray spray filler 1.5 kg
A gray, universal 2K polyester spray filler with excellent filling properties. It is used in automotive body repair, mechanical engineering, and the furniture industry. After mixing, the filler has a pot life of approximately 25 to 30 minutes. After 30 minutes of drying time at 60°C, the filler can be sanded with a 150 to 240 grit sandpaper. This product is intended for professional use only Adhesion on which surface? - Steel plate - Aluminum - Wood - Thermally galvanized bodywork sheet - Galvanized metal sheet - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to be filled and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. Before each application, clean and degrease the entire surface to be painted with silicone remover. Do not apply to thermoplastic or acidic products (reaction primers). Before spraying Unispray, dry-sand with P180-320 and then degrease with silicone remover, then apply filler. Using too little or too much hardener can cause stains in the top coat. If necessary, use a maximum of 10% thinner. Steel substrates: Pre-clean with silicone remover, then sand with P120 and then degrease with silicone remover. Aluminum substrates: Pre-clean with silicone remover, then sand with P220 and then degrease with silicone remover. Galvanized surfaces: Pre-clean with silicone remover, then sand with P220 and then degrease with silicone remover. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Liquid hardener in a plastic jar
€31,20 €27,06
-
Airo Tack Metall metal bonding 50ml
Airo Tack Metall was specifically developed for metal bonding. This powerful 2K adhesive dries air-drying. Its compact size makes it easy to use in a caulking gun with a plastic adapter. Supplied without the required Mixer Tip Round for 2K glue.
€14,57 €12,29
-
Airo Nitro mixer 0.1kg
A gray-green, fast-drying 1K filler based on nitrocellulose resin, packaged in an easy-to-squeeze tube. This filler is ideal for removing minor damage such as scratches or stone chips. Smoothing out minor imperfections is also no problem. The filler is easy to apply with a putty knife or with your finger for difficult areas. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from underneath, for example, with a wooden surface. After allowing the filler to dry for 20 minutes, it can be sanded with grit P180 to P400. When applying multiple (thin) coats, allow approximately one hour for drying between each coat. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image)
€7,42 €6,27
-
Airo Hardener paste red 50gr. - tube
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with dark color 2.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€4,37 €3,75
-
Airo hardener for acrylic Primefill Fuller 4:1 - 250 ml
A high solids hardener for the Airo Acryl Primefill 4:1. (excl. matching quantity of Airo Acryl Primefill)
€10,29 €8,60
-
Airo Acrylic Thinner NORMAL - 1 liter
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€13,83 €11,59
-
Airo TOP Primefill white 500ml
Airo TOP Primefill is a new formula primer in an aerosol can. Because it's in an aerosol can, you can easily reach all areas for treatment. The primer can be applied as a fine finish and dries very quickly. Once dry, it can be sanded to a smooth, pore-free surface. Exceptional adhesion to plastic, metal, galvanized and galvanized sheet metal, aluminum, wood, and painted surfaces. Available in different colours.
€19,43 €16,55
-
Airo TOP Primefill light gray 500ml
Airo TOP Primefill is a new formula primer in an aerosol can. Because it's in an aerosol can, you can easily reach all areas for treatment. The primer can be applied as a fine finish and dries very quickly. Once dry, it can be sanded to a smooth, pore-free surface. Exceptional adhesion to plastic, metal, galvanized and galvanized sheet metal, aluminum, wood, and painted surfaces. Available in different colours.
€19,49 €16,55
-
Airo Masking Tape 38mm x 50m
High-quality masking tape. This product is heat-resistant up to 80°C. The tape is stretchable and tear-resistant, making it easy to use even when applying primer. It is solvent-resistant and leaves no adhesive residue. Available in various sizes. This masking tape is suitable for automotive repair, industrial applications, and painting.
€5,13 €3,64
-
Airo Hardener paste red 40gr. - sleeve
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color 1.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€5,39 €4,63
-
Airo Fix & Seal MS Polymer Kit Black 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€13,00 €10,84
-
Airo Tack Plastic Superfast 30sec-50ml
Airo Tack Plastic Mediumfast repairs plastic parts in 120 seconds. This powerful 2K adhesive dries in 120 seconds. Its small size makes it easy to use in a caulking gun with a plastic adapter. Supplied without the required Mixer Tip Round for 2K glue.
€12,98 €11,18
-
Airo Spritzfüller grey 1.5 kg
A gray 2K polyester spray filler with excellent filling properties. It is used in automotive body repair, mechanical engineering, and the furniture industry. After mixing, the filler has a pot life of approximately 20 to 25 minutes. After 30 minutes of drying time at 60°C, the filler can be sanded with a 150 to 240 grit sandpaper. Adhesion on which surface? - Steel plate - Iron - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Galvanized sheet metal - Aluminum - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to be filled and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If necessary, sand with a P80 to P150 grit. Before each application, clean and degrease the entire surface to be painted with silicone remover. Do not apply to thermoplastic or acidic products (reaction primers). Once the filler is dry, sand with a P150 to P240 grit. Too little or too much hardener can cause stains in the topcoat. If necessary, use a maximum of 5% thinner. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Liquid hardener in a plastic jar
€27,62 €23,78
-
Airo Soft filler 1 kg
A white/beige 2K polyester filler with a wide range of applications. Ideal for all filler work in body repair shops, carpentry workshops, and furniture manufacturing. It's also suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester - When processing on galvanised metal sheet, use Airo Unipol as a base! Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
€16,61 €14,31
-
Airo Mixer Tips Round (10 pcs.)
Special NEW mixer tips for mixing Womix, 2K adhesive from Airo Tack Plastic, and Metall, among other products. This attachment simply slides and twists onto the top connection of the products. Packed per 10 pieces for an attractive price.
€14,95 €9,79
-
Airo Fix & Seal MS Polymer kit white 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€12,76 €10,84
-
Airo Epoxy Grund Universal primer 1 ltr
A beige 2-component (spray) primer based on epoxy resin with strong adhesion to various substrates, particularly aluminum and galvanized parts. It cures quickly, is water-resistant, and offers excellent rust protection. After mixing, the primer has a pot life of 8 hours. It is dust-dry after just 20 minutes and sandable after 4 to 5 hours at 20°C. The primer is sanded with a 150 to 240 grit sandpaper after 4 to 5 hours of curing time. Adhesion on which surface? - Steel plate - Iron - Aluminum - Galvanized base - Glass fiber reinforced plastic based on polyester Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If in doubt, degrease the surface with a clean cloth to improve adhesion. Mix the base with the hardener in a 3:1 ratio (add thinner to your liking if necessary). This mixture can be applied with a spray gun with a 1.5 to 1.7 mm nozzle at a pressure of 1.8 to 2 bar. It can be sanded after approximately 4 to 5 hours of curing time or resprayed. Once the product is applied below the temperature of +10°C, the drying time becomes significantly longer. Drying time +20°C - dust dry after 20 minutes, can be sprayed over after 4 hours, complete drying time 12 hours +60°C – drying time 40 minutes (with a layer thickness of approx. 50 µm) Storage and processing advice - Do not process below +10°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of primer, packed in a tin (see image) - liquid hardener paste in a can of 15 grams
€30,21 €26,05
-
Mirka Hand sanding block 70x125 mm velcro
The Airo Grip Sanding Block has an ergonomic handle for a secure grip. A special connection for a Ø21mm dust extraction system is located on the back. The Velcro sanding base has holes for dust extraction.
€44,66 €38,79
-
Airo Unipol filler 3 kg
Airo Unipol is a beige 2K universal polyester filler with a wide range of applications. It can be used as a coarse or fine filler, has a short curing time, and is easy to sand. After 20 minutes of curing, the filler can be sanded with grit sizes P80 to P280. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 60 grams
€175,82 €142,04
-
Airo Grip Abrasive RED LINE Disc 150mm
These extra-fine sanding discs with 15 (8+6+1) holes fit almost all common random orbital sanders. The hook-and-loop backing ensures optimal adhesion. The sandpaper is plastic-film-based, making it super strong and moisture-resistant. A sturdy hook-and-loop backing with aluminum oxide grit is double-bonded to prevent clogging and maintain sharpness longer.
€33,87 €27,01
-
Pneumatic dosing device 3kg tubes
This dispensing device saves money by efficiently dispensing filler and hardener pneumatically at the correct ratio. The device can be mounted on a wall, including mounting hardware. The central lever allows you to open the air supply, and the lever on the bottom will release the filler and hardener when opened. On the underside is a plate that immediately seals the filler and hardener. It's a solid, neatly finished device, made entirely of sturdy steel components. The hole is centered in the base plate for the filler. Other connections for other brands are also available upon request. The device can be used with Airo Unipol 3kg, Airo Multi Green 2.3kg and Airo Soft 3kg, among others.
€1.376,61 €1.169,62
You have seen 24 out of 117 products