Homepage
-
Airo Hand Cleaner 1ltr
Hand Cleaner is a hand soap for removing glue, sealant, and paint. Unlike other products, this soap is gentle on your hands, preventing them from drying out or irritating. Applying a silicone layer to your hands before working is also no longer necessary with this product.
€26,20 €22,00
-
Airo Hardener paste white 25gr. - tube
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€3,38 €2,89
-
Airo Hardener paste white 40gr. - sleeve
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color 1.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€5,43 €4,63
-
Airo HS Clearcoat Ultra Plus 2:1 - 1ltr
Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C. Supplied without matching hardener
€33,13 €28,50
-
Airo HS Clearcoat Ultra Plus 2:1 - 5ltr
Airo HS Ultra Plus Clearcoat is a high-quality 2K high-solids clearcoat with excellent gloss and durability. It offers excellent resistance to UV radiation, fuels, and weather conditions. Ideal for professional bodywork. Suitable for use on - Acrylic primer (Airo Acryl Füller) - Water-based base coat - Solvent-based base coat Instructions for use Mix 2 parts clearcoat with 1 part Airo Hardener HS Ultra Plus. Thin with Airo Acrylic Thinner if necessary. Spray with a 1.3 to 1.4 mm nozzle at a pressure of 2 to 2.5 bar. Apply 2 coats, allowing 10 to 15 minutes between coats. Allow the coat to dry within the pot life of approximately 4 hours at 20°C. Storage and processing advice - Do not process below +15°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - 5 liters of clear lacquer, packed in a tin - Hardener must be ordered separately
€148,31 €132,71
-
Airo HS Clearcoat Ultra Plus SET - 5ltr
**This product is a set of clear lacquer with normal hardener** Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C.
€235,52 €207,22
-
Airo HS Profit Line Clear coat 2:1 - 5ltr
Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C.
€152,94 €133,76
-
Airo GTI Adhesive Cloths
The Airo GTI Tack Cloths are special tack cloths for dusting surfaces immediately before painting or spraying. These cloths remove dust, flies, and small contaminants from the surface without leaving any residue. Scope of application - For painting cars and bodywork - Varnishing furniture and wood - Spray work on various surfaces Instructions for use Unfold the tack cloth and gently smooth it over the surface to be painted. Apply light pressure and move the cloth in one direction. The cloth attracts and traps dust and dirt. Use each cloth only once for optimal results. Store unused cloths in their original packaging. Supplied as standard - Package with adhesive cloths (see package for quantity)
€3,33 €2,79
-
Airo Plastic Adapter for caulking gun
Adapter for using 50ml cartridges in a traditional caulking gun. This product is designed for Airo Tack products. This is a robust and cost-effective solution compared to purchasing a separate mixing gun. Packed per piece.
€19,95 €17,09
-
Airo Lackspray primer 500ml
Airo Paint Spray is a high-quality primer for treating both treated and untreated surfaces. Thanks to its fast drying and excellent coverage, you won't have to wait long. The paint is also resistant to petrol, chemicals, and weather influences. It's ideal as a pretreatment for topcoats with nitrocellulose, alkyd resin, and 1K and 2K acrylic paints. Suitable for metal, wood, pottery, glass, and various types of plastic.
€15,55 €9,48
-
Airo Magnetic Foil Cutting Blades
The Airo Magnetic Film Cutting Blades are specially designed for precisely cutting masking and cover film. Their magnetic properties make them easy to store and prevent them from getting lost in the workshop. Scope of application - Cutting masking film - Cutting of cover foil - Removing tape and foil Instructions for use Use the blades only for cutting foil and tape. Replace the blade when it is no longer sharp enough for a clean cut. Store the blades on a magnetic surface or in the included holder for safe storage. Supplied as standard - Set of magnetic foil cutting blades (see packaging for quantity)
€73,02 €64,56
-
Airo Masking Tape 19mm x 50m
High-quality masking tape. This product is heat-resistant up to 80°C. The tape is stretchable and tear-resistant, making it easy to use even when applying primer. It is solvent-resistant and leaves no adhesive residue. Available in various sizes. This masking tape is suitable for automotive repair, industrial applications, and painting.
€2,72 €1,83
-
Airo Mixer Tips Round (10 pcs.)
Special NEW mixer tips for mixing Womix, 2K adhesive from Airo Tack Plastic, and Metall, among other products. This attachment simply slides and twists onto the top connection of the products. Packed per 10 pieces for an attractive price.
€14,95 €9,79
-
Airo Multi filler 1.5 kg
This is a beige 2K polyester filler that can be used as an alternative to Unipol. Airo Multi is a slightly finer and more flexible filler than Unipol. This filler can be used as a normal or fine filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 40 grams
€30,00 €25,28
-
Airo Multi filler 3 kg
Airo Multi is a beige 2K polyester filler that can be used as an alternative to Unipol. Airo Multi is a slightly finer and more flexible filler than Unipol. This filler can be used as a normal or fine filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 60 grams
€56,24 €48,02
-
Airo Multi-Green filler 1.1 kg
This light green 2K polyester filler is made with NEW raw materials and contains fewer solvents. Airo Multi Green is a fine filler that can be used universally as a coarse or finishing filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! *Tin is exactly the same as Unipol 1.5kg Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 40 grams
€29,69 €25,35
-
Airo Multi-Green filler 2.3 kg
This light green 2K polyester filler is made with NEW raw materials and contains fewer solvents. Airo Multi Green is a fine filler that can be used universally as a coarse or finishing filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! *Can is exactly the same as Multi 3kg Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 60 grams
€53,07 €44,63
-
Airo Nitro kombispachtel 1kg
A grayish-green, fast-drying 1K filler based on nitrocellulose synthetic resin. This filler is ideal for removing minor damage such as scratches or stone chips. Smoothing out minor imperfections is also no problem. The filler is easy to apply with a putty knife or with your finger for difficult areas. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from underneath, for example, with a wooden surface. After allowing the filler to dry for 20 minutes, it can be sanded with grit P180 to P400. When applying multiple (thin) coats, allow approximately one hour for drying between each coat. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image)
€28,01 €24,11
-
Airo Oversprayable static film 4x300m
The Airo 4mx300m Sprayable Static Film is a large-format, self-adhesive masking film for intensive use. The long roll is particularly advantageous for workshops with high masking film usage. Specifications - Width: 4 meters - Length: 300 meters - Adhesion: static (glue-free) Supplied as standard - 1 roll of Airo sprayable static film 4m x 300m
€103,65 €89,85
-
Airo Resprayable static film 5x120m
The Airo Oversprayable Static Film 5m x 120m is a wide, self-adhesive masking film that adheres using static electricity. No adhesive, no residue – ideal for quickly covering vehicle parts. Specifications - Width: 5 meters - Length: 120 meters - Adhesion: static (glue-free) Supplied as standard - 1 roll of Airo spray-on static foil 5mx120m
€71,33 €59,79
-
Airo Resprayable static film 6x100m
The Airo Oversprayable Static Film 6m x 100m is a self-adhesive masking film that adheres to smooth surfaces without adhesive using static electricity. The film is oversprayable and effectively protects against overspray during painting. Specifications - Width: 6 meters - Length: 100 meters - Adhesion: static (glue-free) Scope of application - Covering windows, bumpers and body parts - Protection during spraying work - Professional bodywork workshop Instructions for use Cut the film to the desired length. Press the film onto the surface to be protected – the film adheres using static electricity, not adhesive. After spraying, simply remove the film without leaving any adhesive residue. Supplied as standard - 1 roll of Airo spray-on static foil 6mx100m
€72,79 €59,00
-
Airo Plastic filler 0.5 kg/SB
White 2K polyester filler with a wide range of applications. Ideal for all filler work in auto body repair, carpentry, and furniture manufacturing. Suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 15 grams
€11,90 €9,95
-
Airo Plastic filler 1 kg
White 2K polyester filler with a wide range of applications. Ideal for all filler work in auto body repair, carpentry, and furniture manufacturing. Suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
€17,68 €15,23
-
Airo Quatro Mixer Tips 2k (10 pcs.)
Special mixer tips for mixing (older models) Womix and 2k cartridges, among other things. This attachment slides easily onto the top connection of the products. **NOTE: Does not fit the Airo TACK 2k kits, for this you will need to use the " Airo Mixertip ROUND ". Packed per 10 pieces for an attractive price.
€13,00 €8,52
You have seen 144 out of 241 products