Car body filler
-
Airo Plastic filler 0.5 kg/SB
White 2K polyester filler with a wide range of applications. Ideal for all filler work in auto body repair, carpentry, and furniture manufacturing. Suitable for small boat repairs above the waterline. Easy to apply, hardens quickly, and sands easily. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 15 grams
€11,90 €9,95
-
Airo Nitro kombispachtel 1kg
A grayish-green, fast-drying 1K filler based on nitrocellulose synthetic resin. This filler is ideal for removing minor damage such as scratches or stone chips. Smoothing out minor imperfections is also no problem. The filler is easy to apply with a putty knife or with your finger for difficult areas. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from underneath, for example, with a wooden surface. After allowing the filler to dry for 20 minutes, it can be sanded with grit P180 to P400. When applying multiple (thin) coats, allow approximately one hour for drying between each coat. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image)
€28,01 €24,11
-
Airo Multi-Green filler 2.3 kg
This light green 2K polyester filler is made with NEW raw materials and contains fewer solvents. Airo Multi Green is a fine filler that can be used universally as a coarse or finishing filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! *Can is exactly the same as Multi 3kg Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 60 grams
€53,07 €44,63
-
Airo Multi-Green filler 1.1 kg
This light green 2K polyester filler is made with NEW raw materials and contains fewer solvents. Airo Multi Green is a fine filler that can be used universally as a coarse or finishing filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper! *Tin is exactly the same as Unipol 1.5kg Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 40 grams
€29,69 €25,35
-
Airo Multi filler 3 kg
Airo Multi is a beige 2K polyester filler that can be used as an alternative to Unipol. Airo Multi is a slightly finer and more flexible filler than Unipol. This filler can be used as a normal or fine filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 60 grams
€56,24 €48,02
-
Airo Multi filler 1.5 kg
This is a beige 2K polyester filler that can be used as an alternative to Unipol. Airo Multi is a slightly finer and more flexible filler than Unipol. This filler can be used as a normal or fine filler. It doesn't shrink, is easy to sand, and has excellent stability. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Galvanized metal sheet - Hot-dip galvanized bodywork sheet - Steel plate - Aluminum - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Acid-curing primers - Wash primer - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying grains may develop after this time. The filler can be sanded after approximately 20 minutes. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - Red hardener paste in plastic tube of 40 grams
€30,00 €25,28
-
Airo Flexi filler 2 kg
A fast-curing gray, elastic 2K polyester filler with excellent adhesion to various plastics. Ideal for repairing damaged bumpers and spoilers. Can be overpainted with acrylic filler and 2K lacquers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Bumpers and spoilers made of plastic or polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€37,67 €31,42
-
Airo Fix Repair - Set 0.8 kg/SB
Highly reactive polyester resin. Combined with glass mats or glass fabric, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry (non-greasy) and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of resin, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams - Glass mat 330g/m2 á 1/2 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€32,29 €26,95
-
Airo Fix Repair - Set 0.25kg/SB
Highly reactive polyester resin. Combined with glass mats or glass fibers, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 8 grams - Glass mat 330g/m2 á 1/8 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€16,43 €10,86
-
Airo Faserpoly filler 0.6 kg/SB
A strong, light-yellow polyester resin with long glass fibers that cures quickly. The filler is highly resistant to water, gasoline, mineral oil, diluted acids, and alkalis. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€19,32 €16,59
-
Airo Faserplast filler 0.8 kg/SB
Faserplast is an olive-green, fiberglass-based 2K polyester filler for working through rusted bodywork parts. This filler is a perfect blend of filler and short polyester fibers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit! Adhesion on which surface? - Steel plate - Galvanized metal sheet Do not apply on - Aluminum - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€17,42 €14,77
You have seen 35 out of 35 products