Best seller
-
€29,95 €19,45
-
€59,88 €55,27
-
€48,55 €41,76
-
€24,55 €17,81
-
€24,45 €16,45
-
€59,95 €48,45
-
€9,45 €7,49
-
Airo Liquid Paste - 60 ml
Cyclohexanone peroxide, slowed down with phthalic acid ester and diacetone alcohol. As a free-radical additive for the curing of unsaturated polyester resins, which have been pre-accelerated with cobalt. By using the correct ingredients in the hardener, Airo fillers will cure properly within the specified time. No guarantee can be given when using other brands. To be used for - Airo spray filler Instructions for use The liquid hardener is specifically designed for hardening polyester spray fillers. Carefully add 1.7% hardener to the spray filler for proper reaction. This hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as may contact with dirt, ash, rust, or metal grindings. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Transparent liquid hardener in a plastic tube with a screw cap Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€10,89 €6,75
-
Airo Hardener for Washprimer 0.5 ltr
The hardener is combined with the Airo Wash Primer. The hardener is specially developed for a perfect bond with the Airo Wash Primer. The hardener is mixed 2:1 with the Wash Primer. Excellent adhesion on galvanized sheet metal, hot-dip galvanized bodywork, steel sheet metal, and aluminum.
€14,58 €9,93
-
Airo hardener for acrylic Primefill Fuller 4:1 - 250 ml
A high solids hardener for the Airo Acryl Primefill 4:1. (excl. matching quantity of Airo Acryl Primefill)
€13,78 €9,67
-
€18,55 €14,41
-
Airo Hardener HS Ultra Plus 2:1 -2.5ltr
Hardener for Acrylic Clearcoat HS Ultra Plus in a 2:1 mixing ratio. Available in various hardening options: normal, short, and extra short. The special hardener, combined with Acrylic Clearcoat HS Ultra Plus, produces a high gloss and is non-yellowing. Drying time: -Normally 30 to 35 minutes at +60 °C -Shortly 20 to 25 minutes at +60 °C -Extra short 10 to 15 minutes at +60 °C. Supplied without matching paint
€87,48 €83,56
-
Airo Unispray spray filler 1.5 kg
A gray, universal 2K polyester spray filler with excellent filling properties. It is used in automotive body repair, mechanical engineering, and the furniture industry. After mixing, the filler has a pot life of approximately 25 to 30 minutes. After 30 minutes of drying time at 60°C, the filler can be sanded with a 150 to 240 grit sandpaper. This product is intended for professional use only Adhesion on which surface? - Steel plate - Aluminum - Wood - Thermally galvanized bodywork sheet - Galvanized metal sheet - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to be filled and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. Before each application, clean and degrease the entire surface to be painted with silicone remover. Do not apply to thermoplastic or acidic products (reaction primers). Before spraying Unispray, dry-sand with P180-320 and then degrease with silicone remover, then apply filler. Using too little or too much hardener can cause stains in the top coat. If necessary, use a maximum of 10% thinner. Steel substrates: Pre-clean with silicone remover, then sand with P120 and then degrease with silicone remover. Aluminum substrates: Pre-clean with silicone remover, then sand with P220 and then degrease with silicone remover. Galvanized surfaces: Pre-clean with silicone remover, then sand with P220 and then degrease with silicone remover. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Liquid hardener in a plastic jar
€29,78 €24,90
-
Airo TOP Primefill white 500ml
Airo TOP Primefill is a new formula primer in an aerosol can. Because it's in an aerosol can, you can easily reach all areas for treatment. The primer can be applied as a fine finish and dries very quickly. Once dry, it can be sanded to a smooth, pore-free surface. Exceptional adhesion to plastic, metal, galvanized and galvanized sheet metal, aluminum, wood, and painted surfaces. Available in different colours.
€21,88 €15,47
-
Airo TOP Primefill light gray 500ml
Airo TOP Primefill is a new formula primer in an aerosol can. Because it's in an aerosol can, you can easily reach all areas for treatment. The primer can be applied as a fine finish and dries very quickly. Once dry, it can be sanded to a smooth, pore-free surface. Exceptional adhesion to plastic, metal, galvanized and galvanized sheet metal, aluminum, wood, and painted surfaces. Available in different colours.
€21,88 €15,47
-
Airo TOP Primefill dark gray 500ml
Airo TOP Primefill is a new formula primer in an aerosol can. Because it's in an aerosol can, you can easily reach all areas for treatment. The primer can be applied as a fine finish and dries very quickly. Once dry, it can be sanded to a smooth, pore-free surface. Exceptional adhesion to plastic, metal, galvanized and galvanized sheet metal, aluminum, wood, and painted surfaces. Available in different colours.
€21,88 €15,47
-
Airo Tack Window sealant MS 290ml
Airo Tack Window sealant is a black MS 1K polymer sealant ideal for bonding windows. Its unique composition provides excellent adhesion to existing window sealant. It also works on glass and ceramic edges without the need for a primer. The Tack Window window sealant is UV-resistant and has very good adhesion.
€26,01 €20,67
-
Airo Tack Plastic Universal 120sec-50ml
Airo Tack Plastic Mediumfast repairs plastic parts in 120 seconds. This powerful 2K adhesive dries in 120 seconds. Its small size makes it easy to use in a caulking gun with a plastic adapter. Supplied without the required Mixer Tip Round for 2K glue.
€15,23 €10,40
-
Airo Tack Plastic Mediumfast 90sec-50ml
Airo Tack Plastic Mediumfast repairs plastic parts in 120 seconds. This powerful 2K adhesive dries in 120 seconds. Its small size makes it easy to use in a caulking gun with a plastic adapter. Supplied without the required Mixer Tip Round for 2K glue.
€15,23 €10,40
-
Airo Tack Metall metal bonding 50ml
Airo Tack Metall was specifically developed for metal bonding. This powerful 2K adhesive dries air-drying. Its compact size makes it easy to use in a caulking gun with a plastic adapter. Supplied without the required Mixer Tip Round for 2K glue.
€15,83 €11,07
-
Airo Superflex filler 3 kg
This is a very white 2K filler. This polyester filler is characterized by its exceptional fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - White hardener paste in plastic tube of 60 grams
€47,98 €42,16
-
Airo Superflex filler 2.5 kg
This is a very white 2K filler. This polyester filler is characterized by its exceptional fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 50 grams
€31,66 €27,29
-
Airo Superflex filler 1.5 kg
This is a very white 2K filler. This polyester filler is characterized by its exceptional fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tube (see image) - White hardener paste in plastic tube of 40 grams
€26,11 €22,71
-
Airo Superflex filler 1 kg
This is a very white 2K filler. This polyester filler is characterized by its exceptional fineness and easy sanding. The sanded surface is pore-free. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Wood - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - White hardener paste in plastic tube of 25 grams
€16,88 €13,80
You have seen 168 out of 241 products