Best seller
-
Airo HS Clearcoat Ultra Plus SET - 5ltr
**This product is a set of clear lacquer with normal hardener** Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C.
€235,52 €207,22
-
Airo HS Clearcoat Ultra Plus 2:1 - 5ltr
Airo HS Ultra Plus Clearcoat is a high-quality 2K high-solids clearcoat with excellent gloss and durability. It offers excellent resistance to UV radiation, fuels, and weather conditions. Ideal for professional bodywork. Suitable for use on - Acrylic primer (Airo Acryl Füller) - Water-based base coat - Solvent-based base coat Instructions for use Mix 2 parts clearcoat with 1 part Airo Hardener HS Ultra Plus. Thin with Airo Acrylic Thinner if necessary. Spray with a 1.3 to 1.4 mm nozzle at a pressure of 2 to 2.5 bar. Apply 2 coats, allowing 10 to 15 minutes between coats. Allow the coat to dry within the pot life of approximately 4 hours at 20°C. Storage and processing advice - Do not process below +15°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - 5 liters of clear lacquer, packed in a tin - Hardener must be ordered separately
€148,31 €132,71
-
Airo HS Clearcoat Ultra Plus 2:1 - 1ltr
Acrylic Clear Coat HS Ultra Plus contains no more than 420g of solvent per liter of ready-to-spray solution. It is applied as a clear coat over metallic base paints or solid colors. It is resistant to chemical and mechanical stresses. The paint dries with a glossy, hard surface. The paint films are elastic and scratch-resistant. Airo Acrylic Clear Coat HS Ultra Plus is weather- and fade-resistant, even under harsh climatic conditions. After mixing (depending on the type of hardener), the clearcoat has a pot life of 1 to 6 hours at +20°C. After 7 minutes of flash-off, the paint dries in 10 to 45 minutes at +60°C. Supplied without matching hardener
€33,13 €28,50
-
Airo Hardener paste white 40gr. - sleeve
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color 1.5kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€5,43 €4,63
-
Airo Hardener paste white 25gr. - tube
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with light color Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€3,38 €2,89
-
Airo Hand Cleaner 1ltr
Hand Cleaner is a hand soap for removing glue, sealant, and paint. Unlike other products, this soap is gentle on your hands, preventing them from drying out or irritating. Applying a silicone layer to your hands before working is also no longer necessary with this product.
€26,20 €22,00
-
Airo Grip Pad UNI support pad 150mm
The Airo Grip Pad UNI backing pad 150mm is a universal velcro backing pad for eccentric sanders with a 150mm disc diameter. The pad features optimal ventilation openings for maximum dust extraction and is compatible with various sander brands. Specifications - Diameter: 150mm - Attachment: Velcro (hook and loop) - Number of holes: 15 - Suitable for: eccentric sanders 150mm Instructions for use Remove the old backing pad from the sander. Attach the new Airo Grip Pad UNI by pressing it firmly onto the drive disc. Check that the pad is properly secured before use. Replace the backing pad when the Velcro is worn or the pad is visibly damaged. Compatible with oa - Mirka DEROS and DEXOS - Festool ETS and ETSC - Rupes LHR and iBrid - And various other brands of sanders 150mm
€48,91 €41,73
-
Airo Glass fabric matt 190g/m2 - 1m2
Glass fibre fabric for repairing holes in combination with repair resin on car bodies and glass fibre reinforced plastic parts exposed to high loads. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to the correct size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Glass fiber mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€16,81 €14,09
-
Airo Glass fabric matt 190g/m2 - 0.5m2
Glass fibre fabric for repairing holes in combination with repair resin on car bodies and glass fibre reinforced plastic parts exposed to high loads. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to the correct size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Glass fiber mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€9,35 €7,94
-
Airo Glass Mat 300g/m2 - 1m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€10,52 €9,12
-
Airo Glass Mat 300g/m2 - 0.5m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€6,67 €5,55
-
Airo Glass Mat 225g/m2 - 1m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€11,13 €9,33
-
Airo Glass Mat 225g/m2 - 0.5m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€6,90 €5,75
-
Airo Fix Repair - Set 0.8 kg/SB
Highly reactive polyester resin. Combined with glass mats or glass fabric, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry (non-greasy) and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of resin, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams - Glass mat 330g/m2 á 1/2 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€32,29 €26,95
-
Airo Fix Repair - Set 0.25kg/SB
Highly reactive polyester resin. Combined with glass mats or glass fibers, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 8 grams - Glass mat 330g/m2 á 1/8 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€16,43 €10,86
-
Airo Fix & Seal MS Polymer kit white 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€12,76 €10,84
-
Airo Faserpoly filler 0.6 kg/SB
A strong, light-yellow polyester resin with long glass fibers that cures quickly. The filler is highly resistant to water, gasoline, mineral oil, diluted acids, and alkalis. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€19,32 €16,59
-
Airo Faserplast filler 0.8 kg/SB
Faserplast is an olive-green, fiberglass-based 2K polyester filler for working through rusted bodywork parts. This filler is a perfect blend of filler and short polyester fibers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit! Adhesion on which surface? - Steel plate - Galvanized metal sheet Do not apply on - Aluminum - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€17,42 €14,77
-
Airo Acrylic Thinner NORMAL - 5 liters
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€61,95 €52,72
-
Airo Acrylic Thinner SLOW - 5 liters
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€65,31 €56,41
-
Airo Acrylic Thinner SLOW - 1 liter
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€16,62 €13,87
-
Airo Acrylic Thinner SHORT - 5 liters
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€62,94 €54,54
-
Airo Abrasive Scuff Roll Very Fine
Airo Abrasive Scuff Roll is a non-woven abrasive material on rolls that can be used both wet and dry. The abrasive fleece is flexible enough for manually sanding various surfaces. Airo Abrasive Scuff Roll is often used in automotive repair, woodworking, metalworking, and yacht building. The rolls are 10 meters long and 115mm wide. The Abrasive Scuff Roll - Very Fine (red) is particularly intended for roughening unpainted parts (plastic, plywood, aluminium), but also for roughening new sheet metal parts.
€44,53 €37,75
-
Airo Abrasive Scuff Roll Ultra Fine
Airo Abrasive Scuff Roll is a non-woven abrasive material on rolls that can be used both wet and dry. The abrasive fleece is flexible enough for manually sanding various surfaces. Airo Abrasive Scuff Roll is often used in automotive repair, woodworking, metalworking, and yacht building. The rolls are 10 meters long and 115mm wide. The Abrasive Scuff Roll - Ultra Fine (grey) is specifically designed for roughening various surfaces such as 2-component car paints, misting zones and even base materials.
€44,69 €37,75
You have seen 240 out of 242 products