Best seller
-
Airo Glass fabric matt 190g/m2 - 1m2
Glass fibre fabric for repairing holes in combination with repair resin on car bodies and glass fibre reinforced plastic parts exposed to high loads. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to the correct size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Glass fiber mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€13,95 €9,35
-
Airo Glass fabric matt 190g/m2 - 0.5m2
Glass fibre fabric for repairing holes in combination with repair resin on car bodies and glass fibre reinforced plastic parts exposed to high loads. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to the correct size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Glass fiber mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€9,95 €7,36
-
Airo Glass Mat 300g/m2 - 1m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€13,23 €8,49
-
Airo Glass Mat 300g/m2 - 0.5m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€7,45 €4,98
-
Airo Glass Mat 225g/m2 - 1m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€13,95 €8,66
-
Airo Glass Mat 225g/m2 - 0.5m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€7,95 €5,23
-
Airo Foam Abrasive Sheets 115x125mm
The soft and flexible Airo Foam Abrasive Sheets are designed for sanding profiled surfaces and rounded, hard-to-reach corners by hand. Airo Foam Abrasive Sheets are widely used in the automotive, painting, and garage sectors. The foam layer is easy to grip and applies even pressure, reducing the risk of sanding through the surface. The sheets are packed in a handy dispenser box with 200 tear-off sheets per roll.
€57,23 €51,89
-
Airo Fix Repair 5kg
Highly reactive polyester resin. Combined with glass mats or glass fabric, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry (non-greasy) and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of resin, packed in a tin (see image) - 2x red hardener paste in plastic tube of 50 grams Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€114,71 €91,17
-
Airo Fix Repair - Set 0.8 kg/SB
Highly reactive polyester resin. Combined with glass mats or glass fabric, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry (non-greasy) and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of resin, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams - Glass mat 330g/m2 á 1/2 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€29,87 €24,28
-
Airo Fix Repair - Set 0.25kg/SB
Highly reactive polyester resin. Combined with glass mats or glass fibers, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 8 grams - Glass mat 330g/m2 á 1/8 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€15,65 €10,34
-
Airo Fix & Seal MS Polymer kit white 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€12,59 €9,76
-
Airo Faserpoly filler 1.5 kg
A strong, light-yellow polyester resin with long glass fibers that cures quickly. The filler is highly resistant to water, gasoline, mineral oil, diluted acids, and alkalis. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€33,26 €27,48
-
Airo Faserpoly filler 0.6 kg/SB
A strong, light-yellow polyester resin with long glass fibers that cures quickly. The filler is highly resistant to water, gasoline, mineral oil, diluted acids, and alkalis. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€21,78 €14,94
-
Airo Faserplast filler 0.8 kg/SB
Faserplast is an olive-green, fiberglass-based 2K polyester filler for working through rusted bodywork parts. This filler is a perfect blend of filler and short polyester fibers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit! Adhesion on which surface? - Steel plate - Galvanized metal sheet Do not apply on - Aluminum - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€16,58 €13,31
-
Airo Epoxy Grund Universal primer 1 ltr
A beige 2-component (spray) primer based on epoxy resin with strong adhesion to various substrates, particularly aluminum and galvanized parts. It cures quickly, is water-resistant, and offers excellent rust protection. After mixing, the primer has a pot life of 8 hours. It is dust-dry after just 20 minutes and sandable after 4 to 5 hours at 20°C. The primer is sanded with a 150 to 240 grit sandpaper after 4 to 5 hours of curing time. Adhesion on which surface? - Steel plate - Iron - Aluminum - Galvanized base - Glass fiber reinforced plastic based on polyester Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or loose paint residue. If in doubt, degrease the surface with a clean cloth to improve adhesion. Mix the base with the hardener in a 3:1 ratio (add thinner to your liking if necessary). This mixture can be applied with a spray gun with a 1.5 to 1.7 mm nozzle at a pressure of 1.8 to 2 bar. It can be sanded after approximately 4 to 5 hours of curing time or resprayed. Once the product is applied below the temperature of +10°C, the drying time becomes significantly longer. Drying time +20°C - dust dry after 20 minutes, can be sprayed over after 4 hours, complete drying time 12 hours +60°C – drying time 40 minutes (with a layer thickness of approx. 50 µm) Storage and processing advice - Do not process below +10°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of primer, packed in a tin (see image) - liquid hardener paste in a can of 15 grams
€48,22 €42,78
-
Airo Acrylic Thinner NORMAL - 5 liters
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€53,24 €47,49
-
Airo Acrylic Thinner SLOW - 5 liters
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€59,89 €50,81
-
Airo Acrylic Thinner SLOW - 1 liter
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€18,66 €12,50
-
Airo Acrylic Thinner SHORT - 5 liters
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€57,24 €49,14
-
Airo Acrylic Thinner SHORT - 1 liter
Acrylic Thinner is a high-quality thinner for all types of acrylic paints and acrylic primers. Due to its high solvent capacity for acrylic resins, a small amount of this special thinner is sufficient to adjust the spray viscosity. The thinner prevents the formation of bubbles, even with short drying times. Can be used for both Acrylic Primefill Fuller and Acrylic HS & MS lacquers.
€17,14 €11,31
-
Airo Abrasive Scuff Roll Very Fine
Airo Abrasive Scuff Roll is a non-woven abrasive material on rolls that can be used both wet and dry. The abrasive fleece is flexible enough for manually sanding various surfaces. Airo Abrasive Scuff Roll is often used in automotive repair, woodworking, metalworking, and yacht building. The rolls are 10 meters long and 115mm wide. The Abrasive Scuff Roll - Very Fine (red) is particularly intended for roughening unpainted parts (plastic, plywood, aluminium), but also for roughening new sheet metal parts.
€39,88 €34,01
-
Airo Abrasive Scuff Roll Ultra Fine
Airo Abrasive Scuff Roll is a non-woven abrasive material on rolls that can be used both wet and dry. The abrasive fleece is flexible enough for manually sanding various surfaces. Airo Abrasive Scuff Roll is often used in automotive repair, woodworking, metalworking, and yacht building. The rolls are 10 meters long and 115mm wide. The Abrasive Scuff Roll - Ultra Fine (grey) is specifically designed for roughening various surfaces such as 2-component car paints, misting zones and even base materials.
€39,88 €34,01
-
1K Clearcoat high gloss 400ml
Colormatic 1K Clear Coat High Gloss is a fast-drying, UV-resistant clear coat that can be used with all common paint systems. Its excellent flow properties and excellent polishability make it ideal for spot repairs and respraying entire bodywork sections. Thanks to its short drying time, excellent flow and easy polishing, this 2K clearcoat is an excellent choice for spot repairs. Features: -High-gloss and UV-radiation resistant -Quick drying -Very good flow -Suitable for spot repair Processing: -Bring the tin to room temperature, 20°C is ideal. - Thoroughly clean the surface to be sprayed with a silicone cleaner. The area must be dry and free of dust and grease. Shake the can vigorously for about 2 minutes, allowing the mixer to work its magic. If you don't shake it thoroughly, there's a chance of color shifts during spraying. -Preferably spray outdoors or in a well-ventilated area. Indoors, you must cover the area well to protect against fine mist. Cover all areas that should not be sprayed. Ensure good lighting so you can see where you are. Ready to start spraying? First, make a test patch to test how the spray can works and how it's applied. -Apply it at a distance of 25 to 30 cm from the object and move the can back and forth gradually. Apply 2-3 coats of clear lacquer, allowing 2-3 minutes for the coat to dry in between. After curing (24 hours at 20°C), any transitions can be polished to a high gloss. -After use, turn the can upside down and clean the valve. Safety: -An allergic reaction may occur due to the isocyanate used in the product. Do not expose persons with respiratory problems or allergic reactions to vapors or spray mist. -Use a paint fume mask type A2-P2 -Wear protective gloves and safety glasses
€34,88 €28,04
-
1K Car Paint in aerosol can 400ml
This 1K automotive paint is specially color-matched using professional PPG automotive paint and is available in any color. The ColorMatic pre-fill standard aerosol can is pre-filled with propellant and specific additives and then filled with the desired paint color using a filling machine. The wide flat-jet spray nozzle creates a very fine atomization, while the high quality and consistent pressure guarantee the best final result. ColorMatic pre-fill standard is a pre-filled aerosol can containing propellants and solvents, filled with a solvent-based basecoat. This basecoat must be finished with a clearcoat. Where can I find my color code? Processing: -Bring the tin to room temperature, 20°C is ideal. - Thoroughly clean the surface to be sprayed with a silicone cleaner. Larger bare surfaces should be primed first with the appropriate primer. The area must be dry and free of dust and grease. Shake the can vigorously for about 2 minutes, allowing the mixer ball to work its magic. If you don't shake it thoroughly, there's a chance of color shifts during spraying. -Preferably spray outdoors or in a well-ventilated area. Indoors, you must cover the area well to protect against fine mist. Cover all areas that should not be sprayed. Ensure good lighting so you can see where you are. Ready to start spraying? First, make a test patch to test how the spray can works and how it's applied. Apply it from a distance of 25 to 30 cm from the object, moving the can back and forth gradually. Don't try to achieve a perfectly smooth result with the first coat; this layer is purely for buildability and coverage. After the paint is applied, a clear coat will need to be sprayed over it. This can be a 1K or 2K clear coat. 2K clear coat is much stronger and resistant to gasoline. Safety: -An allergic reaction may occur due to the isocyanate used in the product. Do not expose persons with respiratory problems or allergic reactions to vapors or spray mist. -Use a paint fume mask type A2-P2 -Wear protective gloves and safety glasses Do you have a color that is mother of pearl? Then you will have to order two spray cans to make the right color. Supplied individually and can NOT exchangeable or returned!
€37,57 €29,89
You have seen 240 out of 240 products