Products
-
Airo Faserplast filler 2 kg
Faserplast is an olive-green, fiberglass-based 2K polyester filler for working through rusted bodywork parts. This filler is a perfect blend of filler and short polyester fibers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit! Adhesion on which surface? - Steel plate - Galvanized metal sheet Do not apply on - Aluminum - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€26,44 €22,80
-
Airo Faserpoly filler 0.6 kg/SB
A strong, light-yellow polyester resin with long glass fibers that cures quickly. The filler is highly resistant to water, gasoline, mineral oil, diluted acids, and alkalis. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams
€21,78 €14,94
-
Airo Faserpoly filler 1.5 kg
A strong, light-yellow polyester resin with long glass fibers that cures quickly. The filler is highly resistant to water, gasoline, mineral oil, diluted acids, and alkalis. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Aluminum - Galvanized sheet metal - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€33,26 €27,48
-
Airo Fix & Seal MS Polymer Kit Gray 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€12,59 €9,76
-
Airo Fix & Seal MS Polymer kit white 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€12,59 €9,76
-
Airo Fix & Seal MS Polymer Kit Black 290ml
Airo Fix & Seal MS Polymer Sealant is a 1K sealant that remains permanently elastic after curing. It is a high-quality sealant with elastic properties that can be overpainted with 2K paints after curing. The Fix & Seal sealant is primarily used for vibrating structures and for sealing seams in bodywork components such as side panels, fenders, wheel arches, etc. It is also frequently used in construction, workshops, the metal industry, and container construction. Available in different colours.
€12,59 €9,76
-
Airo Fix Repair - Set 0.25kg/SB
Highly reactive polyester resin. Combined with glass mats or glass fibers, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 8 grams - Glass mat 330g/m2 á 1/8 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€15,65 €10,34
-
Airo Fix Repair - Set 0.8 kg/SB
Highly reactive polyester resin. Combined with glass mats or glass fabric, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry (non-greasy) and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of resin, packed in a tin (see image) - Red hardener paste in plastic tube of 25 grams - Glass mat 330g/m2 á 1/2 m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€29,87 €24,28
-
Airo Fix Repair 5kg
Highly reactive polyester resin. Combined with glass mats or glass fabric, it can be used to repair car bodies or damaged areas of GRP parts. Airo FIX and glass mats can also be used to create small GRP parts. After curing, Airo Fix is dry (non-greasy) and easy to sand. Adhesion on which surface? - Steel plate - Glass fiber reinforced plastic based on polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Make sure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed so that the filler cannot attract moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 10 minutes, as drying grains may develop after this time. After approximately 25 to 30 minutes of curing time, the Airo Fix can be sanded with P80 to P280 grit. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of resin, packed in a tin (see image) - 2x red hardener paste in plastic tube of 50 grams Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€114,71 €91,17
-
Airo Flexi filler 0.5 kg/SB
A fast-curing gray, elastic 2K polyester filler with excellent adhesion to various plastics. Ideal for repairing damaged bumpers and spoilers. Can be overpainted with acrylic filler and 2K lacquers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Bumpers and spoilers made of plastic or polyester Do not apply on - Wash primer - Acid-curing primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 15 grams Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€21,23 €11,41
-
Airo Flexi filler 2 kg
A fast-curing gray, elastic 2K polyester filler with excellent adhesion to various plastics. Ideal for repairing damaged bumpers and spoilers. Can be overpainted with acrylic filler and 2K lacquers. After 20 minutes of curing time, the filler can be sanded with a P80 to P280 grit sandpaper. Adhesion on which surface? - Bumpers and spoilers made of plastic or polyester Do not apply on - Wash primer - Acid-hardening primers - Nitrocellulose primer - Synthetic primer Instructions for use Sand the surface to which the filler will be applied and remove any dust. Ensure there is no rust, grease, dirt, or (loose) paint residue. If in doubt, degrease the surface with a clean cloth for better adhesion. Always check that the surface is properly sealed to prevent the filler from attracting moisture from below, for example, with a wooden surface. Apply the desired amount of filler to the putty knife and mix it with approximately 2% hardener for the best result. Try not to work the filler for longer than 4 to 6 minutes, as drying granules may develop in the filler after this time. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Store at +20°C in a closed (airtight) container for at least 12 months Supplied as standard - Indicated quantity of filler, packed in a tin (see image) - Red hardener paste in plastic tube of 50 grams
€36,48 €28,45
-
Airo Foam Abrasive Sheets 115x125mm
The soft and flexible Airo Foam Abrasive Sheets are designed for sanding profiled surfaces and rounded, hard-to-reach corners by hand. Airo Foam Abrasive Sheets are widely used in the automotive, painting, and garage sectors. The foam layer is easy to grip and applies even pressure, reducing the risk of sanding through the surface. The sheets are packed in a handy dispenser box with 200 tear-off sheets per roll.
€57,23 €51,89
-
Airo Glass Mat 225g/m2 - 0.5m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€7,95 €5,23
-
Airo Glass Mat 225g/m2 - 1m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€13,95 €8,66
-
Airo Glass Mat 300g/m2 - 0.5m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€7,45 €4,98
-
Airo Glass Mat 300g/m2 - 1m2
Glass mat made of pressed glass fibres for the repair of holes and large damage on corners, edges and curves in metal or glass fibre reinforced plastic parts together with repair resin. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Fiberglass mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you are familiar with the safety recommendations and hazard warnings.
€13,23 €8,49
-
Airo Glass fabric matt 190g/m2 - 0.5m2
Glass fibre fabric for repairing holes in combination with repair resin on car bodies and glass fibre reinforced plastic parts exposed to high loads. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to the correct size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Glass fiber mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€9,95 €7,36
-
Airo Glass fabric matt 190g/m2 - 1m2
Glass fibre fabric for repairing holes in combination with repair resin on car bodies and glass fibre reinforced plastic parts exposed to high loads. To be used for - Airo Fix Instructions for use Clean and sand the surface thoroughly. Cut the fiberglass mat to the correct size. Prepare and mix the required amount of resin. Mark the edges of the area to be repaired, saturate the fiberglass mat with the resin, and place it within the lines. Lightly press the mat onto the surface with a brush. Storage and processing advice - No storage restrictions - Use processing that is valid for the filler or resin Supplied as standard - Glass fiber mat according to specified number of m2 Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€13,95 €9,35
-
Airo Grip Abrasive RED LINE Disc 150mm
These extra-fine sanding discs with 15 (8+6+1) holes fit almost all common random orbital sanders. The hook-and-loop backing ensures optimal adhesion. The sandpaper is plastic-film-based, making it super strong and moisture-resistant. A sturdy hook-and-loop backing with aluminum oxide grit is double-bonded to prevent clogging and maintain sharpness longer.
€32,13 €26,20
-
€34,99 €27,97
-
€0,00
-
Mirka Hand sanding block 70x125 mm velcro
The Airo Grip Sanding Block has an ergonomic handle for a secure grip. A special connection for a Ø21mm dust extraction port is located on the back. The Velcro sanding base has holes for the sandpaper. “ Airo Grip Abrasive Film Sheet ” fits exactly.
€39,99 €34,82
-
Airo Hand Cleaner 1ltr
Hand Cleaner is a hand soap for removing glue, sealant, and paint. Unlike other products, this soap is gentle on your hands, preventing them from drying out or irritating. Applying a silicone layer to your hands before working is also no longer necessary with this product.
€24,95 €20,95
-
Airo Hardener paste red 25gr. - tube
Dibenzoyl peroxide hardener for two-component fillers and polyester resins. It is used as a free-radical additive for the hardening of unsaturated polyester resins pre-accelerated with tribasic aromatic amines. Using the correct ingredients in the hardener ensures that Airo fillers cure well within the specified time. No guarantee can be given when using other brands. To be used for - Airo filler with dark color 1kg Instructions for use Add approximately 2% to 5% hardener to the filler for proper mixing. The hardener is specifically designed for Airo fillers and is not guaranteed to work with other fillers. Above 50°C, the hardener paste may decompose, as it may degrade upon contact with dirt, ash, rust, or metal swarf. CAUTION: Never mix too much hardener! Excessive hardener won't speed up the process, but it can actually cause the paint layer to delaminate or change color. Storage and processing advice - Do not process below +5°C - Recommended processing temperature is between +18°C and +25°C - Store at +20°C in a closed (airtight) container for at least 6 months Supplied as standard - Hardener paste in plastic tube with screw cap Always read the instructions on the packaging carefully before use. Make sure you understand the safety recommendations and hazard warnings.
€5,39 €2,64
You have seen 48 out of 266 products